Manuals
/
Brands
/
Computer Equipment
/
Projector
/
Acer
/
Computer Equipment
/
Projector
Acer
1100E
- page 26
1
26
161
161
Download
161 pages, 1.3 Mb
Altos 1100E Series User’s Guide
1-10
4.
Insert the drive into the drive bay and secure it with two screws.
5.
Connect the signal and power cables to the drive and close the housing panels.
Contents
Main
Page
iii
Join Us to Fight Against Piracy
Page
Page
CD-ROM Safety Warning
FCC Class B Radio Frequency Interference Statement
Table of Contents
Chapter 1 System Housing
Chapter 2 System Board
Page
Chapter 3 BIOS Utility
Page
Chapter 4 SCSISelect Configuration Utility
Index
List of Figures
Page
About This Manual
Manual Structure
Chapter 1 System Housing
Chapter 2 System Board
Chapter 3 BIOS Utility
Conventions
Chapter 1 System Housing
1.1 Stand-alone System
Page
Chapter 1 System Housing 1-3
1.2.2 Rear Panel
Altos 1100E Series Users Guide1-4
1.3 Internal Structure
Page
1.4.2 Left Panel
1.5 Installing Drives
1.5.1 3.5-inch Drive
Page
1.5.2 5.25-inch Drives
Page
1.6 Installing Hot-Swap Cages
BPL3 and BPL5 Hot-Swap Cage Comparison Table
Page
Page
Page
Page
Page
Page
Page
Page
Page
1.7 Installing and Removing a Hot-swappable Redundant Power Supply Module
Page
Page
Page
1.10 SCSI Backplane Board
Page
Page
Page
Jumpers and Connectors
BPL5 Backplane Board
Page
Chapter 2 System Board
2.1 Features
Page
2.2 Major Components
2.3 System Board Layout
Page
2.4.2 Jumper Settings
* Default
2.4.3 Connector Functions
Table 2-2 Connector Functions (continued)
Page
2.6 Installing Components
2.6.1 ESD Precautions
2.6.2 Pre-installation Instructions
2.6.3 Post-installation Instructions
Page
Page
2.8 Installing a Pentium III Processor
Page
2.9 Removing a Pentium III Processor
2.10 Installing the Termination Board
2.11 Memory Upgrade
2.11.1 Memory Configurations
2.11.2 Installing a DIMM
2.11.3 Removing a DIMM
2.11.4 Reconfiguring the System
2.12 Installing Expansion Cards
2.12.1 Installing 32 Bit PCI Cards
2.12.2 Installing an AGP Card
2.13 ASM Pro
2.14 Remote Diagnostic Management
2.14.1 Installing the RDM Module
2.15 Error Messages
2.15.1 Software Error Messages
2.15.2 System Error Messages
Table 2-4 System Error Messages
Table 2-4 System Error Messages (continued)
2.15.3 Correcting Error Conditions
Page
Chapter 3 BIOS Utility
3.1 Entering Setup
Page
3.2 System Information
3.2.1 Processor
Page
Page
Page
3.3 Product Information
3.3.1 Product Name
3.3.2 System S/N
Page
3.4 Disk Drives
Page
Page
If there is no device connected, choose None.
Hard Disk Block Mode
Advanced PIO Mode
Hard Disk Size > 504 MB
Page
3.5 Power Management
3.5.1 Power Management Mode
IDE Hard Disk Standby Timer
System Sleep Timer
3.5.2 Power Switch < 4 sec.
3.5.3 Wakeup Event
Modem Ring
3.6 Startup Configuration
3.6.1 Fast POST Mode
Page
Page
3.7 Advanced Configuration
3.7.1 Onboard Devices Configuration
Serial Port 1
Serial Port 2
Parallel Port
3BCh 378h 278h
5 and 7
Operation Mode
Onboard Floppy Disk Controller
Onboard IDE Primary Channel
Page
Chapter 3 - BIOS Utility 3-29
3.7.2 PnP/PCI System Configuration
PCI IRQ Setting
PCI Device Latency Timer
PCI IRQ Sharing
VGA Palette Snoop
Graphics Aperture Size
Plug and Play OS
Reset Resource Assignments
3.7.3 Memory/Cache Configuration
Internal Cache (CPU Cache)
Cache Scheme
Page
3.7.4 CPU Speed Configuration
Bus Frequency
Multiple
Processor Speed
3.7.5 System Event Configuration
System Event Logging
View Event Logs
Event Control
Threshold Settings
3.8 System Security Setup
3.8.1 Disk Drive Control
3.8.2 Setup Password
Setting a Password
Changing or Removing the Setup Password
Bypassing the Setup Password
3.8.3 Power-on Password
Operation Mode
3.9 Date and Time
3.9.1 Date
3.9.2 Time
3.10 Remote Diagnostic Configuration
Chapter 3 - BIOS Utility 3-47
3.11 Load Setup Default Settings
3.12 Abort Settings Change
3.13 Leaving Setup
Page
Chapter 4 SCSI Select Configuration Utility
4.1 SCSISelect Configuration Utility Overview
4.1.1 Default Values
Altos 1100E Series Users Guide 4-2
Table 4-1 Default Settings for SCSI Controller and All Devices
Global Settings for SCSI Controller and All Devices Default Value
Individual Settings for Each SCSI Device Default Value
Page
4.2 SCSISelect Utility Options
4.2.1 Configure/View Host Adapter Settings Menu
Host Adapter SCSI ID
*
SCSI Parity Checking
Host Adapter SCSI Termination
Boot Device Options
SCSI Device Configuration
Initiate Sync Negotiation
Maximum Sync Transfer Rate
Enable Disconnection
Initiate Wide Negotiation
Send Start Unit Command
Advanced Configuration Options
Host Adapter BIOS
Support Removable Disks Under BIOS as Fixed Disks
Page
4.2.2 SCSI Disk Utilities
Format Disk
Verify Disk Media
4.3 Configuring Multiple SCSI Controllers
4.4 SCSI Troubleshooting Checklist
4.5 BIOS Startup Messages
4.5.1 Device connected, but not ready
4.5.2 Start unit request failed
4.5.3 Disk Drive Configuration Problems
Booting the Computer from a SCSI Drive
Using a Standard Drive as C and a SCSI Drive as D
Using a SCSI Drive as C and Another SCSI Drive as D
Page
Index A
B
C
D
E
F
H
I
J
L
M
N
O
P
R
S
