POST Codes Tables
These tables describe the POST codes, drivers, and keys for the POST.
Sec
NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc)
Code | Description |
|
|
0xC2 | MTRR setup |
|
|
0xC3 | Enable cache |
|
|
0xC4 | Establish cache tags |
|
|
0xC5 | Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0. |
|
|
0xCF | Cache Init Finished |
|
|
Memory:
DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC)
| Code | Description |
|
|
|
|
|
| 0xA0 | First memory check point |
|
|
|
|
|
| 0x01 | Enable MCHBAR |
|
|
|
|
|
| 0x02 | Check for DRAM initialization interrupt and reset fail |
|
|
|
|
|
| 0x03 | Verify all DIMMs are DDR or DDR2 and unbuffered |
|
|
|
|
|
| 0x04 | Detect an improper warm reset and handle |
|
|
|
|
|
| 0x05 | Detect if ECC |
|
|
|
|
|
| 0x06 | Verify all DIMMs are single or double sided and not asymmetric |
|
|
|
|
|
| 0x07 | Verify all DIMMs are x8 or x16 width |
|
|
|
|
|
| 0x08 | Find a common CAS latency between the DIMMS and the MCH |
|
|
|
|
|
| 0x09 | Determine the memory frequency and CAS latency to program |
|
|
|
|
|
| 0x10 | Determine the smallest common TRAS for all DIMMs |
|
|
|
|
|
| 0x11 | Determine the smallest common TRP for all DIMMs |
|
|
|
|
|
| 0x12 | Determine the smallest common TRCD for all DIMMs |
|
|
|
|
|
| 0x13 | Determine the smallest refresh period for all DIMMs |
|
|
|
|
|
| 0x14 | Verify burst length of 8 is supported by all DIMMs |
|
|
|
|
|
| 0x15 | Determine the smallest tWR supported by all DIMMs |
|
|
|
|
|
| 0x16 | Determine DIMM size parameters |
|
|
|
|
|
| 0x17 | Program the correct system memory frequency |
|
|
|
|
|
| 0x18 | Determine and set the mode of operation for the memory channels |
|
|
|
|
|
| 0x19 | Program clock crossing registers |
|
|
|
|
|
| 0x20 | Disable Fast Dispatch |
|
|
|
|
|
| 0x21 | Program the DRAM Row Attributes and DRAM Row Boundary registers |
|
|
|
|
|
| 0x22 | Program the DRAM Bank Architecture register |
|
|
|
|
|
| 0x23 | Program the DRAM Timing & and DRAM Control registers |
|
|
|
|
|
| 0x24 | Program ODT |
|
|
|
|
|
| 0x25 | Perform steps required before memory init |
|
|
|
|
|
| 0x26 | Program the receive enable reference timing control register |
|
|
| Program the DLL Timing Control Registers, RCOMP settings |
|
|
|
|
|
|
|
|
|
Chapter 4 | 145 |
