Acer RA19WAANU service manual Display Communications Channel, Panel Timings

< 1.0 lux 10℃

> 24 hours

6

ACER X193HQ

1. Product Specification (continued)

Go to cover page

1.3.8Display Communications Channel

The monitor assembly shall provide a display communications channel that conforms to VESA DDC2Bi hardware requirements. This configuration shall contain the 128-byte EDID file as specified by VESA EDID standard.The monitor should not write to the EDID file for the first two minutes of operation following power-up UNLESS some action taken by the user or the host CPU forces the write (for instance, requesting the serial number via the OSD). Furthermore, it is recommended that CMOS switches be incorporated to isolate the DDC IC from outside connections while the EDID Fault Management is being updated. This is to prevent corruption of the data by attempts to read the data while it is being changed.

1.3.9Firmware Update Function (same ISP function) The update firmware need through from the D-Sub connector, use DDC I2C bus to do update firmware.

1.4PANEL ELECTRICAL

1.4.1General Requirements

The panel used as the display device shall be an WXGA 1366X768 resolution, 19 inch-wide TFT-LCD. This panel shall be approved for use in this monitor.

1.4.2Panel Timings

The controller included with the monitor shall translate all video timings from the CPU that meet the timing requirements listed in Panel specification into timings appropriate for the panel. Under no circumstances may the controller supply the panel with timings that

may result in damage. The controller shall insulate the panel from the CPU , so that the panel shall always be driven per it's own specification regardless of the timings being sent from the CPU.

1.4.3Polarizer Hardness

The outer face of the front polarizer panel shall be covered with a coating with a # 3 hardness value .

1.4.4Backlight Requirements

1.4.4.1General Requirements

The backlight assembly shall be designed to support field replacement at the customer site or authorized service center. The lamps shall have a continuous operating life of at least 40,000 hours at 25 degree. The operating life is defined as having ended when the illumination of light has reached 50% of the initial value.

The lamps shall extend a sufficient amount from the edge of the light guide that sputtering over the life of the lamps shall not cause degradation of the luminance uniformity (such as non-illuminated bands along the edges of the display).

1.4.4.2Lamps Startup Time

The backlight lamps shall start about 2 sec of the time the monitor power switch is pressed or the monitor is restarted from a power - down mode

.The starting time shall stay about 2 sec. for the minimum expected life of the lamps.

Test conditions are as follows :

Ambient Light ----------------------

Temperature--------------------------

Inactive Time -----------------------

1.4.5Defects

1.4.5.1 Visual Inspection

The LCD panel shall be inspected with all pixels set to white,black , red , green , and blue. The color variation, brightness variation , and overall appearance must not be perceived as poor quality by Lite-On . Areas and / or parameters considered questionable shall be subjected to detailed measurements .

1.4.5.2Display Degradation

Over the life of the product , variation of the parameters specified in Panel specification shall be maintained within reasonable limits.The panel must not exhibit any significant defects while in operation ( excluding the CCFL operation ).This does not in any way change the warranty given by the panel manufacturer .

1.4.5.3Light Leakage

Except for the active display area , there shall be no light emission visible from any angle from any other part of the display . For this test , the ambient illumination must follow panel's specification.

1.4.5.4Allowable Defects

No cosmetic defects are allowed except those specified below.The conditions of visual inspections are as follows

For P19W Series.

■Viewing distance is to be approximately 35-50cm ■Ambient illumination is to be 300 to 700 lux. ■Viewing angle shall be at 90 degree.

■Defects not apparent within one minute shall be ignored.