Manuals / Advantech / Computer Equipment / Computer Hardware

Advantech PCA-6187 user manual Copyright Notice

Models: PCA-6187

1 126

Download 126 pages 48.89 Kb

Page 2

Copyright Notice

This document is copyrighted, 2003, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improve- ments to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmit- ted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements upon the rights of third parties which may result from its use.

Acknowledgements

•AWARD is a trademark of Phoenix Technologies Ltd.

•IBM and PC are trademarks of International Business Machines Corpo- ration.

•Intel®, Pentium® 4, and Celeron™ are trademarks of Intel Corporation. •WinBond is a trademark of Winbond Corporation.

All other product names or trademarks are the properties of their respec- tive owners.

Part No. 2002618700	1st. Edition
Printed in Taiwan	Nov 2003

PCA-6187 User’s Manual

ii

Image 2

Advantech PCA-6187 user manual Copyright Notice

Contents

User’s Manual PCA-6187Copyright Notice Technical support Advantech customer services1.0.1 A Message to the Customer Table 1.1 PCA-6187 comparison table PCA-6187 User’s Manual iv1.0.2 Product warranty 1.0.3 Initial Inspection 1.0.4 Release NoteContents 2.12.1 Memory Hole At 15M-16M Advanced Chipset FeaturesIntegrated Peripherals 3.6.21 VGA Setup LAN ConfigurationOnboard Security Setup USB Connector CN6 General Information CHAPTERSome of the features mentioned above are not Chapter 1 Hardware Configuration1.1 Introduction about the specifications of a particular model1.3.1 System 1.2 Features1.3 Specifications 1.3.4 VGA interface 1.3.2 Memory1.3.3 Input/Output Power supply voltage +5 V, ±12 1.3.7 Industrial features1.3.8 Mechanical and environmental specifications 1.3.5 Ethernet LANTable 1.1 Jumpers 1.4 Jumpers and ConnectorsTable 1.2 Connectors Table 1.2 Connectors Table 1.3 SCSI Daughter Board ConnectorsPCA-6187 User’s Manual 1.5 Board Layout Jumper and Connector LocationsFigure 1.1 Jumper and Connector locations CN CN CN CN Figure 1.2 I/O ConnectorsCN 32 CN 31 CN 33 CN 68 Pin for Ultra 50 Pin for Ultra wide SCSI Adaptec AIC-7899Intel 865G 1.6 PCA-6187 Block DiagramPCA-6187 User’s Manual Intel ICH5power is on. Sensitive electronic components 1.7 Safety PrecautionsAlways completely disconnect the power cord can be damaged by sudden power surges. Only1.8.3 Watchdog timer output J2 1.8 Jumper Settings1.8.1 How to set jumpers 1.8.2 CMOS clear J1The interrupt output of the watchdog timer is a 1.9 System MemoryTable 1.5 Watchdog timer output J2 low level signal. It will be held low until theTable 1.6 CPU FSB and memory speed 1.9.2 Dual channel configuration1.9.1 CPU FSB and memory speed 1.10 Memory Installation Procedures 1.11 Processor InstallationPCA-6187 User’s Manual Chapter2 Connecting PeripheralsCHAPTER 2.1 Introduction Chapter 2 Connecting Peripherals2.2 1st & 2nd CN1, CN2 IDE Connectors 2.3 Floppy Drive Connector CN3 2.4 Parallel Port CN42.6 VGA Connector CN7 2.5 USB Ports CN62.7 Ethernet Connector CN8 and CN34 2.8 Serial Ports COM1 CN9 COM2 CN10CN11 2.9 PS/2 Keyboard/Mouse Connector CN11/CN332.10 External Keyboard Connector CN12 CN122.12.1 Power LED CN16 2.11 CPU Fan Connector CN142.12 Front Panel Connectors CN16, 17, 18, 19, 21&29 2.12.2 External speaker CN172.12.6 SM Bus Connector CN29 2.12.3 Reset CN182.12.5 ATX soft power switch CN21 2.12.4 HDD LED CN192.15 Serial ATA interface SA0 and SA1 2.13 ATX feature connector CN202.14 AC-97 Audio interface CN43 CN20CPU Card 2.16 Connecting to SNMP-1000 remote manager2.17 Auxiliary 4-pin power connector ATX1 SNMP-1000Chapter3 Award BIOS SetupCHAPTER 3.1.1 CMOS RAM Auto-backup and Restore Chapter 3 Award BIOS Setup3.1 Introduction If you intend to change the CMOS setting withFigure 3.1 Award BIOS Setup initial screen 3.2 Entering Setup3.3 Standard CMOS Setup Figure 3.2 Standard CMOS features screenFigure 3.3 Advanced BIOS features screen 3.4 Advanced BIOS Features3.4.1 Hard Disk Boot Priority 3.4.2 Virus Warning3.4.7 Boot Other Device 3.4.5 Quick Power On Self Test3.4.6 First/Second/Third Boot Device 3.4.9 Boot UP Floppy Seekbe asked to enter a password. Simply press 3.5 Advanced Chipset FeaturesTo disable security, select “PASSWORD SET DRAM default timings have been carefully cho3.5.2 CAS Latency Time Figure 3.4 Advanced chipset features screen3.5.1 DRAM Timing Selectable 3.5.3 Active to Precharge Delay3.5.9 Memory Hole At 15M-16M 3.5.7 System BIOS Cacheable3.5.8 Video Bios Cacheable 3.5.10 Delay Prior to ThermalChapter3 3.6 Integrated PeripheralsFigure 3.5 Integrated peripherals Figure 3.6 On-Chip IDE Device 3.6.3 On-Chip Serial ATA 3.6.1 IDE HDD Block Mode3.6.2 On-Chip IDE Device 3.6.4 Serial ATA Port0/Port1 Mode3.6.6 USB 2.0 Controller 3.6.11 Onboard LAN Boot ROM3.6.5 USB Controller 3.6.7 USB Keyboard/Mouse Support3.6.13 Onboard Serial Port 3.6.19 Use IR Pins3.6.12 Onboard FDC Controller 3.6.14 Onboard Serial Port3.6.22 EPP Mode Select 3.7 Power Management SetupFigure 3.9 Power management setup screen 3.6.23 ECP Mode Use DMA3.7.2 ACPI function 3.7.1 Power-Supply Type3.7.3 Power Management 3.7.4 Video Off MethodFigure 3.10 PnP/PCI configurations screen 3.8 PnP/PCI Configurations3.7.12 Resume on Alarm 3.7.9 CPU THRM-Throttling3.8.2 Resources Controlled By 3.9 PC Health Status3.8.1 Reset Configuration Data 3.8.3 PCI/VGA Palette Snoop3.9.4 Current CPUFAN Speed 3.11 Password Setting3.10 Spread Spectrum Control 3.9.5 VCORE, +1.5V, VCC3, +5V, +12V, -12V, -5V, VBATV, 5VSBVPlease Enter Your Password 3.12 Save & Exit Setup3.13 Exit Without Saving Please Confirm Your PasswordChapter4 Chipset Software Installation UtilityCHAPTER 4.2 Introduction Chapter 4 Chipset Software Install Utility4.1 Before you begin The files on the software installation CD arebefore installing all the other drivers 4.3 Windows XP Driver SetupWindows system, and it has to be installed This utility is used for the following versions ofPCA-6187 User’s Manual 2. Click Next when you see the following message3. Click Yes when you see the following message 4. Click Next when you see the following message Chapter4PCA-6187 User’s Manual Chapter5 VGA SetupCHAPTER 5.2 Dynamic Video Memory Technology Chapter 5 VGA Setup5.1 Introduction utility has been installed in your system. See 5.3 Windows XP Driver SetupBefore installing this driver, make sure the CSI Chapter 4 for information on installing the CSI1. Please click on Next to continue the installation PCA-6187 User’s Manual3. Click Yes when you see the following message Chapter54. Click on Yes to continue the installation PCA-6187 User’s ManualChapter6 LAN ConfigurationCHAPTER 6.1 Introduction Chapter 6 LAN Configuration6.2 Features CSI utility has been installed in your system 6.3 Installation6.4 Win XP Driver Setup Intel 82547/41/62/51 See Chapter 4 for information on installing the3. Click Next to continue PCA-6187 User’s Manual4. Click Install Software to start the installation procedure Chapter6PCA-6187 User’s Manual Chapter7 SCSI Setup & ConfigurationCHAPTER If any peripheral is running at SE mode, the Chapter 7 SCSI Setup & Configuration7.1 Introduction Ultra 160 SCSI segment will run at speeds up to7.2 Understanding SCSI 7.3 SCSI IDs7.4 Terminating the SCSI Bus change or view current settings, or if you would 7.5 Configuring the SCSI interface with SCSISelectThe default settings are appropriate for most systems. Run SCSISelect if you need toPCA-6187 User’s Manual Advanced Configuration OptionsSync Transfer Rate MBytes/sec If you have difficulty viewing the display, press 7.6 Starting SCSISelectmodes. This feature may not work on some F5 to toggle between color and monochromeTo configure settings for a SCSI device, you Boot Device OptionsSCSI Device Configuration SCSI Bus Interface Definitionstransfer rate enabled using an 8-bit SCSI device that hangs or exhibits other performance problems with 16-bit data Do not change the Advanced Configurationdrives before changing the translation scheme Changing the translation scheme destroys alldata on the drive. Be sure to back your disk 7.7 Using SCSI Disk Utilities 7.8 Installation under Windows 7.9 Windows 9X Driver setup procedure3. Click on Update Driver 4. Click on “Next” 5. Recommend to search for a better driver PCA-6187 User’s Manual7. In the Update Device Driver Wizard click on Next Chapter7PCA-6187 User’s Manual 8. The installation is completed. Click on Finish9. Click on Yes to restart the system Chapter8 USB 2.0 ConfigurationCHAPTER 8.3 Installation Chapter 8 USB 2.0 Configuration8.2 Features 8.1 IntroductionChapter9 Onboard Security SetupCHAPTER Chapter 9 Onboard Security Setup 9.1 IntroductionChapter9 9.2 Windows XP Driver Setup2. Click Next when you see the following message PCA-6187 User’s Manual 3. Click Next when you see the following message4. Click Next when you see the following message Chapter9 6. Click Finish when you see the following message5. Click Next to continue 9.3 Using the OBS Hardware Doctor Utility Chapter9 PCA-6187 User’s Manual AppendixA Programming the Watchdog TimerAppendix A.1.1 Watchdog timer overview A.1 Programming the Watchdog TimerAppendix A Programming the watchdog A.1.2 Reset/ Interrupt selectionUse the function of the watchdog timer Lock W83627HF Unlock W83627H Select register of watchdog timerEnable the function of the watchdog timer AppendixAPCA-6187 User’s Manual Address of register 2EAttribute Table A.1 Watchdog timer registers A.1.4 Example ProgramSet timeout interval as 10 seconds and start counting Dec dx Out dx,al Out dx,al Out dx,al AppendixB I/O Pin AssignmentsAppendix Table B.1 IDE hard drive connector CN1, CN2 B.1 IDE Hard Drive Connector CN1, CN2Appendix B Pin Assignments SignalSignal B.2 Floppy Drive Connector CN3Table B.2 Floppy drive connector CN3 SignalSignal B.3 Parallel Port Connector CN4Table B.3 Parallel port connector CN4 SignalTable B.4 USB1/USB2 connector CN6 B.4 USB Connector CN6B.5 VGA Connector CN7 USB1 SignalSignal B.6 COM1/COM2 RS-232 Serial Port CN9, CN10B.7 Keyboard and Mouse Connnector CN11 Table B.6 COM1/2 RS-232 serial port CN9/10Signal B.8 External Keyboard Connector CN12Table B.7 Keyboard and mouse connector CN11 Table B.8 External keyboard connector CN12Table B.9 CPU Fan Power Connector CN14 B.9 CPU Fan Power Connector CN14B.10 Power LED CN16 Table B.10 Power LED and keylock conn CN16Table B.11 External Speaker Connector CN17 B.11 External Speaker Connector CN17B.12 Reset Connector CN18 Table B.12 Reset connector CN18Table B.13 HDD LED connector CN19 B.13 HDD LED Connector CN19B.14 ATX Feature Connector CN20 Table B.14 ATX feature connector CN20B.17 AC-97 Audio Interface CN43 B.15 ATX Soft Power Switch CN21B.16 H/W Monitor Alarm CN22 Table B.15 ATX soft power switch CN21Signal B.18 SM Bus Connector CN29Table B.18 SM Bus Connector CN Table B.17 AC-97 Audio Interface CN43Addr. range Hex B.19 System I/O PortsTable B.19 System I/O ports DeviceTable B.20 DMA channel assignments B.20 DMA Channel AssignmentsB.21 Interrupt Assignments ChannelTable B.22 1st MB memory map B.22 1st MB Memory MapB.23 PCI Bus Map Addr. range HexPCA-6187 User’s Manual