Advantech PPC-V106 user manual

PPC-V106

Fanless Vehicle Mounted

Terminal with 10.4" TFT LCD

User’s Manual

Contents

Main Page Page Packing List Additional Information and Assistance Page Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betrgt 70dB(A) oder weiger. Page Contents Chapter 1 General Information........................................2 Chapter 2 System Setup.....................................................8 Chapter 3 Hardware and Peripheral Installation.........16 Chapter 4 Jumper Settings and Connectors..................20 Chapter 5 VIA Chipset ....................................................30 Chapter 6 AGP SVGA Setup ..........................................32 Chapter 7 PCI Bus Ethernet Interface...........................36 Chapter 8 Audio ...............................................................40 Chapter 9 USB 2.0............................................................42 Appendix A Programming the Watchdog Timer.............52 Appendix B Pin Assignments .............................................56 Page General Information Chapter 1 General Information 1.1 Introduction 1.2 General Specifications Page Page 1.3 LCD Specifications Page Page Chapter 2 System Setup 2.1 A Quick Tour of the Panel PC Page 2.2 Installation Procedures 2.2.1 Connecting the Power Cord 2.2.2 Connecting the Keyboard or Mouse 2.2.3 Switching On the Power 2.3 Running the BIOS Setup Program 2.4 Installing System Software 2.5 Installing the Drivers Page Page Chapter 3 Hardware and Peripheral Installation 3.1 Overview of Hardware Installation and Upgrading 3.2 Installing the 2.5" Hard Disk Drive (HDD) 3.3 Placing the Rubber Seal 3.4 Installing the Universal Arm Jumper Settings and Connectors Chapter 4 Jumper Settings and Connectors 4.1 Setting Jumpers 4.1.1 Jumpers and Switches 4.1.2 Locating Jumpers and Switches 4.1.3 Connectors Page 4.3 CMOS Clear for External RTC (JP1) 4.4 COM-port Interface 4.4.1 COM2 RS-232/422/485 Setting (JP5) Page 4.4.2 COM1/COM2/COM3/ Pin 9 Output Setting (JP4) Table 4.7: JP3 Setting 4.5 VGA Interface 4.5.1 LCD Panel Power Setting Page Chapter 5 VIA Chipset 5.1 Introduction 5.1.1 Installation 4-in-1 Driver for Windows 98/2000/XP 5.2 Further Information Page Chapter 6 AGP SVGA Setup 6.1 Introduction 6.1.1 Chipset 6.1.2 Display memory 6.2 Installation of SVGA Driver 6.3 Further Information Page Page Chapter 7 PCI Bus Ethernet Interface 7.1 Introduction 7.2 Installation of Ethernet Driver 7.2.1 Installation for Windows 98/ME 7.2.2 Installation for Windows 2000/XP Page Page Chapter 8 Audio 8.1 Introduction 8.2 Installation of Audio Driver Page Chapter 9 USB 2.0 9.1 Installation of USB 2.0 Driver 9.2 Driver Installation for Windows XP 9.3 Driver Installation for Windows 2000 9.4 Driver Installation for Windows ME / 98 / 98SE 9.5 Further Information Page Chapter 10 Touchscreen 10.1 Introduction 10.1.1 General information 10.1.2 General specifications 10.1.3 Environmental Specifications 10.2 Installation of Touchscreen Drivers 10.2.1 Installation of Resistive T/S driver for Windows 98/ME 10.2.2 Installation of Resistive T/S driver for Windows 2000/XP 10.2.3 Installation of Infrared T/S driver for Windows 2000/XP 10.3 Further Information Page A Appendix A Programming the Watchdog Timer A.1 Programming the Watchdog Timer Page Page Page Appendix B Pin Assignments B.1 Inverter Power Connector (CN10) B.2 Internal Speaker Connector (CN14) Table B.1: Inverter power connector (CN10) B.3 Floppy Drive Connector (CN16) Reserved Table B.3: Floppy drive connector (CN16) B.4 IDE Hard Disk Drive Connector (CN15) # low active 59 Appendix B B.5 IR Connector (CN8) Reserved B.6 LVDS Connector (CN4) Pin Signal Pin Signal * VDDSAFE can choose +5V or +12V output via JP2 12 43 B.7 Flat Panel Display Connector (CN2) (Reserved) 34 12 Pin Signal Pin Signal * VDDSAFE can choose +5V or +12V output via JP2 B.8 COM1 B.9 COM2 B.10 COM3 B.11 COM3 Connector (CN 26) B.12 COM 4 Connector (CN 23) B.13 USB Port B.14 Parallel Port Connector (CN11) Table B.4: Parallel Port Connector (CN8) B.15 VGA Connector