Operation Verification

Checking the Maximum Leveled Power

Checking the Maximum Leveled Power

Perform the following procedure to check the maximum leveled power:

1.

Press Preset.

2.

Attach a 50Ω load to the RF OUTPUT. A power sensor, attenuator, or 50Ω termination is an example of

 

a 50Ω load.

3.Press RF On/Off. The RF On annunciator is now displayed.

4.Press Mod On/Off. The Mod Off annunciator is now displayed.

5.Press Amplitude and enter a value from Table 3-1that is applicable to your model and options.

6.If the E82x7D PSG signal generator is equipped with Option 007, press Sweep /List > Sweep Type> Step > Configure Step Sweep.

If the E82x7D PSG signal generator is not equipped with Option 007, press Sweep /List > Configure Step Sweep.

7.Press Freq Start and enter the start frequency value listed in Table 3-1that corresponds to the amplitude value entered in step 5.

8.Press Freq Stop and enter the corresponding stop frequency listed in Table 3-1.

9.Press # Points and enter the number of corresponding points listed in Table 3-1.

10.Press Return > Sweep > Freq. The SWEEP annunciator is now on and a continuous sweep will begin. During the sweep, the progress bar becomes active on the display, indicating the status of the current sweep.

11.Watch the display and ensure that the Unlevel annunciator does not appear at any time during a full sweep.

The Unlevel annunciator may turn on and off, or remain on; both conditions indicate a failure. If this occurs, refer to “Maximum Leveled Power Check Failure” on page 22 for further instructions.

12.Press Sweep > Off.

13.Repeat steps 5-12for each frequency range, specific to your model number and options.

Maximum Leveled Power Check Failure

If a maximum leveled power check fails, perform the following procedure:

1.Verify the limits for that particular option using the data sheet.

2.If the Unlocked annunciator is displayed, refer to the troubleshooting section of the Service Guide.

22

Chapter 3

Page 25 Page 27
Page 26
Image 26
Agilent Technologies E8257D/67D manual Checking the Maximum Leveled Power, Maximum Leveled Power Check Failure
Page 25 Page 27

E8257D/67D specifications

Agilent Technologies has established itself as a leader in the realm of electronic testing and measurement, and the E8257D/67D signal generators are prime examples of its commitment to innovation and quality. These advanced signal generators are engineered to meet the rigorous demands of both research and development as well as manufacturing applications.

The E8257D/67D offers a frequency range of up to 67 GHz, making it suitable for a wide array of modern applications, including radar, satellite communications, and advanced wireless technologies. This wide frequency coverage is complemented by outstanding spectral purity and phase noise performance, which are crucial for applications that require high signal fidelity.

One of the standout features of the E8257D/67D is its ability to generate a variety of waveforms. In addition to traditional continuous wave signals, it supports frequency sweeping and pulse modulation, allowing users to design complex test scenarios that simulate real-world conditions. The instrument's high-resolution frequency and amplitude settings provide precision control, essential for characterizing high-performance components.

The E8257D/67D employs advanced digital signal processing technology that enhances both its accuracy and stability. This digital architecture allows for superior linearity and minimized distortion, which are vital parameters in many testing scenarios. Furthermore, the generator’s fast-switching capabilities enable rapid changes in frequency and amplitude, facilitating dynamic testing environments.

In terms of connectivity, the E8257D/67D supports various interfaces, including LAN, USB, and GPIB, allowing for seamless integration into automated test systems. This flexibility not only maximizes productivity but also simplifies system integration and data acquisition.

The user-friendly GUI (Graphical User Interface) of the E8257D/67D enhances the user experience, making it easier to navigate and configure settings. With its comprehensive set of built-in functions and measurement options, users can efficiently perform complex tasks without extensive training.

Overall, the Agilent Technologies E8257D/67D signal generators excel in providing high-performance signal generation capabilities. With its impressive specifications, versatility, and ease of use, it is an ideal choice for engineers and technicians seeking to ensure the highest standards in electronic design and testing. Whether in R&D labs or production lines, the E8257D/67D stands out as a reliable tool for advanced signal generation.
Top Page Image Contents