Manuals / Alcatel Carrier Internetworking Solutions / Computer Equipment / Switch

Alcatel Carrier Internetworking Solutions 7800, 7700 manual Installing Power Supplies, Standalone

Models: 7700 7800

1 68

Download 68 pages 32.62 Kb

Page 16

Standalone

Standalone

The OmniSwitch 7700/7800 can be installed unmounted as a standalone unit. Be sure that the installation location is a stable, flat surface that can accommodate the fully-populatedweight of all switches being installed. One fully-populated OmniSwitch 7700 weighs approximately 128 lbs (58 Kgs); a fully-populated OmniSwitch 7800 weighs approximately 188 lbs (85 Kgs).

Note. OmniSwitch 7700/7800 switches must be installed “right side up.” Never attempt to operate a switch while it is lying on its side.

To install the switch as a standalone unit, follow the steps below:

1Use two or more people to move and position the unpopulated chassis upright on the floor or bench where it is to be installed.

2Be sure that adequate clearance has been provided for chassis airflow and that you have placed the chassis within reach of all required electrical outlets. For recommended airflow allowances, refer to page 7. For environmental and electrical requirements, refer to page 4.

Installing Power Supplies

Next, reinstall the power supplies in the chassis power supply bays by following the steps below.

1First, be sure that you do not install the power supply upside down. When orienting the power supply, note that the on/off switch and power cord socket are located at the bottom of the power supply and the fan is located at the top of the power supply.

2With one hand, grasp the handle at the front of the power supply. Place your other hand under the power supply casing to support its weight.

3Carefully insert the rear of the casing into the power supply bay and slide the power supply back until its connector meets the chassis backplane connector.

MP

A

.

A

10 Installing the Hardware

March 2005

Image 16

Alcatel Carrier Internetworking Solutions 7800, 7700 manual Installing Power Supplies, Standalone

Contents

Getting Started Guide OmniSwitch 7700/7800U.S. Patent No. 6,339,830 Table of Contents Setting the Date and Time Setting Optional System User Documentation on CD March Features OmniSwitch 7700/7800Availability Features OmniSwitch Chassis TypesOmniSwitch Installing the Hardware Items RequiredSite Preparation Environmental RequirementsUnpacking and Installing the Switch Weight ConsiderationsItems Included Unpacking the Chassis5 Carefully remove the protective plastic from the switch chassis Lifting the Chassis Mounting the SwitchAirflow Considerations Chassis Top View Rack-MountingOptional Rack-Mounting Hardware Installing Power Supplies Standalonecannot be accidentally pulled from the socket Using the Grounding Wrist Strap and Chassis Grounding Lug NI Modules CMMs5 Install all remaining modules by repeating steps Installing GBIC Connectors Installing MiniGBIC ConnectorsBlank Cover Plates 16 Installing the HardwareSerial Connection Default Settings Connections and Cablingbaud rate parityEMP to a Switch Ethernet Management Port EMP Cable RequirementsEMP to a Computer or WorkstationBooting the Switch Power Supply AC OKPower Supply DC OK Power Supply OVER TEMPYour First Login Session Logging In to the SwitchSetting IP Address Information for the EMP additional table output not shownUnlocking Session Types the Hardware Users GuideUnlocking All Session Types Unlocking Specified Session TypesChanging the Login Password How many sessions are allowed?Setting the System Time Zone Setting the Date and TimeSetting Optional System Information Specifying an Administrative ContactSpecifying the Switch’s Location Specifying a System NameModifying the Serial Connection Settings Viewing Your ChangesSaving Your Changes 26 Your First Login Session1 default and 2. For example additional table output not shown28 Your First Login Session 9 Return to the CLI prompt by entering exit at the boot promptMarch CLI Basics CLI Assistance FeaturesSyntax Checking Command Line ? Help Partial Keyword CompletionDeleting Characters 30 CLI BasicsInserting Characters Previous Command RecallPrefix Recognition Prefix Prompt Command History32 CLI Basics Command Logging Enabling Command LoggingCommon CLI Commands pageOffline Configuring Generating Snapshots of the Current ConfigurationScheduling a Configuration File to be Applied at a Later Time Syntax CheckingBoot and Image Files boot.params Fileboot.cfg File Files and DirectoriesImage Files enhanced security features for the switchWorking Directory Working and Certified DirectoriesCertified Directory write memory command Working and Certified Are Different 40 Files and DirectoriesNon-Redundant Configurations Loading SoftwareRedundant Configurations to the Switch Management Guide or the CLI Reference Guide6 Use the install command after the software files have been transferred to the switch via FTP. For example Browser Compatibility Using WebViewRequired Image Files Logging In to WebView Navigating WebView“Configuration Options” Toolbar Main “Configuration Group” Toolbar46 Using WebView Online Help TroubleshootingAdditional Information OmniSwitch 7700 Slot Numbering OmniSwitch 7800 Slot NumberingHardware Basics Chassis Slot NumberingChassis Management Module CMM CMM RedundancyOmniSwitch CMM Slot LocationsOmniSwitch 50 Hardware BasicsCMM Front Panel Temperature/Fan Status LEDsStatus LEDsENI Modules Network Interface NI ModulesGNI Modules Gigabit Interface Converters GBICs Miniature Gigabit Interface Converters MiniGBICsOS7-ENI-C24 Front Panel Module Status LEDsStatus LEDsOS7-ENI-FM12 Front Panel Module Status LEDsStatus LEDsOS7-ENI-P24 Front Panel Ethernet Port Power LEDsPower on LAN Ethernet Ports ModuleOS7-GNI-U2 Front Panel Module Status LEDsGigabit Ethernet Port LEDs Module Status LEDsOS7-GNI-U12 Front Panel Module Status LEDsGigabit Ethernet Port LEDs Module Status LEDsOS7-GNI-C12 Front Panel Module Status LEDsEthernet Port LEDs Module Status LEDsOmniSwitch 7700/7800 Getting Started Guide OmniSwitch 7700/7800 Hardware Users GuideOmniSwitch CLI Reference Guide OmniSwitch 7700/7800/8800 Switch Management GuideMarch User Documentation on CDUser Documentation on CD OmniSwitch 7700/7800/8800 Advanced Routing Configuration Guide General Information