Grounding Instructions

The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

The washer is equipped with a cord having an equipment-grounding conductor and a three-prong grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING

Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly grounded.

W327

DO NOT modify the plug provided with the washer – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that in Figure 11, the qualified electrician should correct the problem.

Step 8: Check Installation

Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly.

Run washer through one complete cycle to make sure it is operating properly.

Vending

Meter Case

The factory mounted coin meter case does not include the service door lock, coin drawer, coin drawer lock or keys. These parts must be ordered (at extra cost) according to the purchaser’s requirements direct from the manufacturer of your choice.

Installation

NOTE: On models with standard capacity meter case and high capacity meter case models starting with Serial Nos. beginning 1010, you have the option of using a screw type lock or a 1/4 turn lock on the meter case service door. If you choose to use a screw lock, then the special bracket (located inside the meter case) must be used. DO NOT use the special bracket if a 1/4 turn lock is used. High capacity meter case models with Serial Nos. beginning 0910 through 1010 use 1/4 turn lock only.

Coin Drawer Security (Models with standard capacity meter case and high capacity meter case models starting with Serial Nos. beginning 1010 only) – For additional security, drill out the two pilot holes on each side of the front of the meter case to 1/4 or 5/16 inch (6.4 or 7.9 mm) holes and install a bicycle lock through these holes.

NOTE: An 8 in. (20.32 cm) coin drawer is required for models with standard capacity meter case and high capacity meter case models starting with Serial Nos. beginning 1010. High capacity meter case models with Serial Nos. beginning 0910 through 1010 require a 7.21 in. (18.31 cm) coin drawer.

Models Prepped for Card Reader

The machine is shipped from the factory with the Electronic Control Diagnostic Harness Assembly unplugged. To avoid unauthorized manual programming or vending, perform the following steps.

1.Open control panel. Refer to Figure 12.

2.Locate diagnostic harness on electronic control.

3.Plug connectors for “white/black” wire and “red/blue” wire together.

1

FLW6R

1Control Panel

Figure 12

803148

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

13

Page 14 Page 16
Page 15
Image 15
Alliance Laundry Systems FLW1526C manual Vending, Grounding Instructions, Check Installation, Meter Case
Page 14 Page 16

FLW1526C specifications

The Alliance Laundry Systems FLW1526C is a cutting-edge commercial washer designed specifically for durability and efficiency in laundry environments. This front-loading washer is part of Alliance’s range of high-capacity models, making it an ideal choice for laundromats, hotels, and other businesses that require reliable and consistent washing solutions.

One of the standout features of the FLW1526C is its impressive capacity. With a 26-pound load capacity, this washer can handle sizable laundry tasks, reducing the number of cycles needed and increasing productivity. Efficiency is further enhanced by the washer's advanced water extraction capabilities, which help minimize drying times and energy consumption.

The FLW1526C utilizes innovative technology to optimize performance. It is equipped with an intuitive microprocessor control system that simplifies operation and allows for customizable wash cycles. Users can select from a variety of preset cycles tailored to different fabric types and cleaning needs, ensuring that garments receive the best treatment possible while maintaining their integrity.

Durability is a hallmark of Alliance Laundry Systems design, and the FLW1526C reflects this commitment. Constructed with a robust stainless steel wash basket, it can withstand the rigors of frequent use without compromising performance. Additionally, the heavy-duty cabinet is designed to resist wear and tear, ensuring a long lifespan for the machine.

Another significant feature of the FLW1526C is its eco-friendly design. It operates with water-saving technologies that help reduce overall consumption without sacrificing wash quality. This not only leads to cost savings over time but also supports sustainable business practices.

The machine's user-friendly interface is designed for simplicity, making it accessible for operators of all skill levels. The large door provides easy loading and unloading access, and the modern aesthetic of the machine complements any laundry facility environment.

Overall, the Alliance Laundry Systems FLW1526C combines high capacity, advanced technology, and robust construction to meet the demands of commercial laundry operations. Its efficiency, flexibility, and user-friendly design make it a valuable investment for businesses looking to enhance their laundry capabilities.
Top Page Image Contents