|
|
|
|
|
|
| Features in |
|
|
| 18 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level | Description | AR400 | AR7x5 | AR750S / AR770S |
| Rapier i |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012697 | IPsec, ENCO | 2 | Decrypting a large IPsec ESP packet sometimes caused the router or switch to | Y | Y | Y |
| Y | Y | - |
| - | - | - | - |
|
|
| reboot. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012710 | Core | 2 | Soft errors can generate exceptions that would cause the router or switch to | - | - | Y |
| - | - | - |
| - | - | - | - |
|
|
| reboot. Soft errors are spontaneous changes in the information stored in a digital |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| circuit, caused by physical effects. The router or switch’s handling of such errors |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| has been improved, so that it recovers without rebooting when possible. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012741 | Core, File, | 2 | The command create config=filename set did not copy the configuration file | - | - | - |
| Y | Y | Y |
| Y | Y | Y | - |
| Stack |
| to all switches in the stack, but only saved the file onto the current switch. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012757 | OSPF | 2 | The router or switch correctly accepted the command add ospf redistribution | Y | Y | Y |
| Y | Y | Y |
| Y | Y | Y | Y |
|
|
| protocol=static followed by the command set ospf asexternal=on or nssa. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| However, the command create config did not create a valid configuration file |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| from these commands. If the router or switch used that configuration after a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| reboot, it gave the error “Redistribution for specified routing protocol - already |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| exists” and did not use the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. The router or switch now correctly saves and uses |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012820 | DHCP | 2 | When the switch had two DHCP snooping classifiers applied across all 48 ports, | - | - | - |
| - | - | - |
| - | Y | - | - |
| Snooping, |
| and maxleases was set to 10 or more on each port, the switch rebooted. |
|
|
|
|
|
|
|
|
|
|
|
|
| Switch |
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012821 | IP Gateway | 2 | When adding, deleting or updating subnet routes of a more general route, the | - | - | - |
| Y | Y | Y |
| Y | Y | Y | Y |
|
|
| software and hardware IP route tables sometimes became unsynchronised. The |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| same issue sometimes also occurred when updating ECMP routes. This could |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| cause the router or switch to forward packets to unexpected next hops. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version