Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-FS750/24POE manual Unpacking the Switch

Models: AT-FS750/24POE

1 54

Download 54 pages 12.51 Kb

Page 38

Unpacking the Switch

Chapter 2: Installation

Unpacking the Switch

To unpack the switch, perform the following procedure:

1. Remove all components from the shipping package.

Note

Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis.

2.Place the switch on a level, secure surface.

3.Ensure that the following hardware components are included in your switch package. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.

One AT-FS750/24POE Fast Ethernet Smart switch and the following:

Two rack-mount brackets

Six rack-mount bracket screws

Four rubber feet (for desktop use)

One power cord

Documentation CD

38

Image 38

Allied Telesis AT-FS750/24POE manual Unpacking the Switch

Contents

AT-FS750/24POE Installation GuideFast Ethernet Smart Switch Copyright 2008 Allied Telesis, Inc U.S. Federal Communications Commission Electrical Safety and Emissions StandardsFCC Class A, EN55022 Class A, CISPR Class A, C-TICK, CE Radiated EnergyTranslated Safety Statements Contents Environmental Specifications ContentsPhysical Specifications Power SpecificationsFigures Figure 1. RJ-45 Connector and Port Pin LayoutTables IEEE 802.3af Class vs. Power Levels TablesTable 1. Safety Symbols MDI Pin Signals 10Base-T or 100Base-TXTables ˆ “Where to Find Web-based Guides” on page Prefaceˆ “Safety Symbols Used in this Document” on page ˆ “Contacting Allied Telesis” on pageMeaning Safety Symbols Used in this DocumentSymbol DescriptionWhere to Find Web-based Guides AT-FS750/24POE Fast Ethernet Smart Switch Installation GuideOnline Support Email and Telephone Support Returning Products WarrantyContacting Allied Telesis For Sales or Corporate InformationOverview ChapterFeatures Uplink Combo Ports Front and Back PanelsSystem LEDs 10/100Base Twisted Pair Ports Port LEDsTwisted Pair Ports PortsUplink Combo Ports AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide connected, the SFP port takes precedent over the twisted pair portState LEDs10/100Base-T POE Port LEDs DescriptionDescription 10/100Base-T Non-POE Port LEDsState Description Uplink Combo Port LEDsState State DescriptionPower Supply For the power requirements, refer to “Power Specifications” on pagePower over Ethernet Class Minimum PowerMaximum Power UsageEthernet Switching Basics MAC Address Table Duplex ModeStore and Forward Back Pressure and Flow Controldata again, the switch stops forcing collisions. This is referred to as back pressure Power Workgroup Topology Network TopologiesCollapsed Backbone Chapter 1 Overview Installation ChapterReviewing Safety Precautions Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E21 Selecting a Site for the Switch Speed CablingMaximum Type of CableUnpacking the Switch Installing the Switch on a Desktop Installing a Switch in a Rack AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide Chapter 2 Installation Installing an Optional SFP Transceiver Figure 12. Inserting the SFP Connecting the Fiber Optic Cables Cabling and Powering On the SwitchConnecting the Twisted Pair Cables Powering On the Switch Figure 16. Plugging in the AC Power Cord Starting a Management Session Troubleshooting ChapterChapter 3 Troubleshooting Environmental Specifications Technical SpecificationsPhysical Specifications Power SpecificationsSignal Safety and Electromagnetic Emissions CertificationsConnectors and Port Pinouts 1 RX+ 2 RX 3 TX+ 6 TX Table 9. MDI-X Pin Signals 10Base-T or 100Base-TXSignal Appendix A Technical Specifications