Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-FS750/24POE manual Powering On the Switch

Models: AT-FS750/24POE

1 54

Download 54 pages 12.51 Kb

Page 46

Powering On the Switch

Chapter 2: Installation

1. Remove the dust plug from the SFP, as shown in Figure 14.

10/100/1000Base-T 25

CLASS

LASER PR 1

ODUCT

SFP	10/100/1000Base-T
	26
	SFP
	UPLINK
	PO
	RTS

1102

Figure 14. Removing the Dust Plug from the SFP

2. Connect the fiber optic cable to the SFP port, as shown in Figure 15.

10/100/1000Base-T 25

CLASS		1
LASER
	PRODUCT

SFP		10/100/1000Base-T
		26
		SFP
	UPLINK	PORTS
		PORTS

1103

Powering On the Switch

Figure 15. Connecting the Fiber Optic Cable

To power on the switch, perform the following procedure:

1.Plug the power cord into the AC power connector on the back of the switch, as shown in Figure 16.

46

Image 46

Allied Telesis AT-FS750/24POE manual Powering On the Switch

Contents

Fast Ethernet Smart Switch Installation GuideAT-FS750/24POE Copyright 2008 Allied Telesis, Inc U.S. Federal Communications Commission Electrical Safety and Emissions StandardsFCC Class A, EN55022 Class A, CISPR Class A, C-TICK, CE Radiated EnergyTranslated Safety Statements Contents Environmental Specifications ContentsPhysical Specifications Power SpecificationsFigures Figure 1. RJ-45 Connector and Port Pin LayoutTables IEEE 802.3af Class vs. Power Levels TablesTable 1. Safety Symbols MDI Pin Signals 10Base-T or 100Base-TXTables ˆ “Where to Find Web-based Guides” on page Prefaceˆ “Safety Symbols Used in this Document” on page ˆ “Contacting Allied Telesis” on pageMeaning Safety Symbols Used in this DocumentSymbol DescriptionWhere to Find Web-based Guides AT-FS750/24POE Fast Ethernet Smart Switch Installation GuideOnline Support Email and Telephone Support Returning Products WarrantyContacting Allied Telesis For Sales or Corporate InformationOverview ChapterFeatures Uplink Combo Ports Front and Back PanelsSystem LEDs 10/100Base Twisted Pair Ports Port LEDsUplink Combo Ports PortsTwisted Pair Ports AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide connected, the SFP port takes precedent over the twisted pair portState LEDs10/100Base-T POE Port LEDs DescriptionState 10/100Base-T Non-POE Port LEDsDescription State Uplink Combo Port LEDsDescription State DescriptionPower Supply For the power requirements, refer to “Power Specifications” on pagePower over Ethernet Class Minimum PowerMaximum Power UsageEthernet Switching Basics MAC Address Table Duplex ModeStore and Forward Back Pressure and Flow Controldata again, the switch stops forcing collisions. This is referred to as back pressure Power Workgroup Topology Network TopologiesCollapsed Backbone Chapter 1 Overview Installation ChapterReviewing Safety Precautions Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E21 Selecting a Site for the Switch Speed CablingMaximum Type of CableUnpacking the Switch Installing the Switch on a Desktop Installing a Switch in a Rack AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide Chapter 2 Installation Installing an Optional SFP Transceiver Figure 12. Inserting the SFP Connecting the Twisted Pair Cables Cabling and Powering On the SwitchConnecting the Fiber Optic Cables Powering On the Switch Figure 16. Plugging in the AC Power Cord Starting a Management Session Troubleshooting ChapterChapter 3 Troubleshooting Environmental Specifications Technical SpecificationsPhysical Specifications Power SpecificationsConnectors and Port Pinouts Safety and Electromagnetic Emissions CertificationsSignal Signal Table 9. MDI-X Pin Signals 10Base-T or 100Base-TX1 RX+ 2 RX 3 TX+ 6 TX Appendix A Technical Specifications