Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-FS750/24POE manual Inserting the SFP

Models: AT-FS750/24POE

1 54

Download 54 pages 12.51 Kb

Page 44

Figure 12. Inserting the SFP

Chapter 2: Installation

4.Slide the SFP transceiver into an SFP slot on the switch, as shown in Figure 12.

10/100/1000Base-T 25

L	CLAS
	ASER	S 1
		PRO
		DUCT

SFP	10/100/1000Base-T
	26
	SFP
	UPLINK
	PO
	RTS

1100

Figure 12. Inserting the SFP

5. Repeat steps 2 through 4 if you are installing another SFP transceiver.

Note

SFP transceivers are dust sensitive. When a fiber optic cable is not installed, or when you store the SFP, always keep the plug in the optical bores. When you do remove the plug, keep it for future use.

Note

Unnecessary removal and insertion of an SFP can lead to premature failure.

For information about cabling for the SFP, consult the documentation that was shipped with the SFP.

44

Image 44

Allied Telesis AT-FS750/24POE manual Inserting the SFP

Contents

AT-FS750/24POE Installation GuideFast Ethernet Smart Switch Copyright 2008 Allied Telesis, Inc Electrical Safety and Emissions Standards FCC Class A, EN55022 Class A, CISPR Class A, C-TICK, CEU.S. Federal Communications Commission Radiated EnergyTranslated Safety Statements Contents Contents Physical SpecificationsEnvironmental Specifications Power SpecificationsFigures Figure 1. RJ-45 Connector and Port Pin LayoutTables Tables Table 1. Safety SymbolsIEEE 802.3af Class vs. Power Levels MDI Pin Signals 10Base-T or 100Base-TXTables Preface ˆ “Safety Symbols Used in this Document” on pageˆ “Where to Find Web-based Guides” on page ˆ “Contacting Allied Telesis” on pageSafety Symbols Used in this Document SymbolMeaning DescriptionWhere to Find Web-based Guides AT-FS750/24POE Fast Ethernet Smart Switch Installation GuideWarranty Contacting Allied TelesisOnline Support Email and Telephone Support Returning Products For Sales or Corporate InformationOverview ChapterFeatures Front and Back Panels System LEDs 10/100Base Twisted Pair PortsUplink Combo Ports Port LEDsTwisted Pair Ports PortsUplink Combo Ports AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide connected, the SFP port takes precedent over the twisted pair portLEDs 10/100Base-T POE Port LEDsState DescriptionDescription 10/100Base-T Non-POE Port LEDsState Description Uplink Combo Port LEDsState State DescriptionPower Supply For the power requirements, refer to “Power Specifications” on pagePower over Ethernet Minimum Power Maximum PowerClass UsageEthernet Switching Basics MAC Address Table Duplex ModeStore and Forward Back Pressure and Flow Controldata again, the switch stops forcing collisions. This is referred to as back pressure Power Workgroup Topology Network TopologiesCollapsed Backbone Chapter 1 Overview Installation ChapterReviewing Safety Precautions Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E21 Selecting a Site for the Switch Cabling MaximumSpeed Type of CableUnpacking the Switch Installing the Switch on a Desktop Installing a Switch in a Rack AT-FS750/24POE Fast Ethernet Smart Switch Installation Guide Chapter 2 Installation Installing an Optional SFP Transceiver Figure 12. Inserting the SFP Connecting the Fiber Optic Cables Cabling and Powering On the SwitchConnecting the Twisted Pair Cables Powering On the Switch Figure 16. Plugging in the AC Power Cord Starting a Management Session Troubleshooting ChapterChapter 3 Troubleshooting Technical Specifications Physical SpecificationsEnvironmental Specifications Power SpecificationsSignal Safety and Electromagnetic Emissions CertificationsConnectors and Port Pinouts 1 RX+ 2 RX 3 TX+ 6 TX Table 9. MDI-X Pin Signals 10Base-T or 100Base-TXSignal Appendix A Technical Specifications