Alpine CDA-9815, CDA-9813, CDA-9811 owner manual 39-EN

1Antenna Receptacle

2Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna, if applicable.

This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier, or a signal processor, etc.

3Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your

#Right Front (–) Speaker Output Lead (Gray/Black)

$ Right Rear (–) Speaker Output Lead (Violet/Black)

%Right Rear (+) Speaker Output Lead (Violet)

&Left Rear (+) Speaker Output Lead (Green)

( Left Rear (–) Speaker Output Lead (Green/Black) ) Left Front (–) Speaker Output Lead (White/Black)

~Left Front (+) Speaker Output Lead (White)

+Ai-NET Connector

amplifier or signal processor.

4Audio Interrupt In Lead (Pink/Black)

5Illumination Lead (Orange)

This lead may be connected to the vehicle's instrument cluster illumination lead. This will allow the backlighting of the unit to dim whenever the vehicle's lights are turned on.

6Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.

7Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle's battery.

8Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.

9Choke Coil with Fuse Holder (20A)

!Power Supply Connector

"Right Front (+) Speaker Output Lead (Gray)

Connect this to the output or input connector of other product (CD Changer, Equalizer, etc.) equipped with Ai- NET.

You can input TV/video sound by connecting an optional Ai- NET/RCA Interface cable (KCA-121B) to this component.

,Ai-NET Cable (Included with CD Changer)

-Front Output RCA Connectors

RED is right and WHITE is left.

. Rear Output RCA Connectors

RED is right and WHITE is left.

/Subwoofer RCA Connectors

RED is right and WHITE is left.

:RCA Extension Cable (Sold Separately)

;Setting the 3WAY/2 WAY switch

Set the 3way/2way switch according to your audio system.

<System Switch

When connecting a processor or divider using Ai-NET, place this switch in the EQ/DIV position. When no device is connected, leave the switch in the NORM position.

Be sure to turn the power off to the unit before changing the switch position.

The X-Over Switch position for a two-way system (frequency range is divided between highs for front/rear and lows for the Subwoofer).

The position of the X-Over switch : F/R/Sub-W

Front high range	Front high range
speaker (L)	speaker (R)
Rear high range	Rear high range
speaker (L)	speaker (R)
Low range	Low range
speaker (L)	speaker (R)

The X-Over Switch position for a three-way system whose frequency range is divided among the highs (Front), mids (Rear), and lows (Subwoofer).

The position of the X-Over switch: 3WAY

High range	High range
speaker (L)	speaker (R)
Mid range	Mid range
speaker (L)	speaker (R)
Low range	Low range
speaker (L)	speaker (R)

Output of this unit :

Front output Rear output SUB-W output

•Use the SUB-W output cord to connect the unit to the low range speaker.

•You can use the built-in amplifier to output the front output/rear output.

•You cannot adjust the fader when set to 3WAY.

To prevent noise/interference in the audio system.

•Locate the unit and route the leads at least 10 cm away from the car harness.

•Keep the battery power leads as far away from other leads as possible.

•Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.

•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors, contact them for further information.

•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

39-EN