Basic Operation
g DN BAND |
|
| Rotary encoder | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
f UP
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal preference.
1 Press the CENTER f button to select the BASS (bass Centre frequency) control mode.
→BASS → TREBLE → normal mode
Press the g DN or f UP button to select the desired bass centre frequency.
→60Hz → 80Hz → 100Hz → 200Hz
Emphasizes the displayed Bass frequency ranges.
Press the BAND button to select the desired bass Band Width.
→B.Width1 → B.Width2→ B.Width3 → B.Width4 (Wide)← ........................... →(Narrow)
Changes the bass boost band width to narrow or wide. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency.
Turn the Rotary encoder to select the desired bass Level
You can emphasize or weaken the bass frequency.
NOTES
•If no buttons are pressed within 15 seconds, the Bass control setting will be turned off automatically.
•The settings of the Bass Level will be individually memorized for each source (FM, MW (LW), CD, etc.) until the setting is changed. Once you set Bass frequency and Bass Band Width for one of sources (FM, MW (LW), CD, etc.), this setting becomes effective for all those sources.
•This function is inoperable when DEFEAT is ON.
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal preference.
1 Press the CENTER f button select on the TREBLE (treble Centre frequency) control mode.
→BASS → TREBLE → normal mode
Press g DN or f UP button to select the desired treble centre frequency.
→10kHz → 12.5kHz → 15kHz → 17.5kHz
Emphasizes the displayed Treble frequency ranges.
Turn the Rotary encoder to select the desired Treble Level
You can emphasize the treble frequency.
NOTES
•If no buttons are pressed within 15 seconds, the Treble control setting will be turned off automatically.
•The settings of the Treble Level will be individually memorized for each source (FM, MW (LW), CD, etc.) until the setting is changed. Once you set Treble frequency for one of sources (FM, MW (LW), CD, etc.), this setting becomes effective for all those sources.
•This function is inoperable when DEFEAT is ON.
Adjusting the built-in Crossover
The High and Low Pass Filters on this unit can be adjusted to suit your personal taste.
1 Press and hold the
→ | HPF |
| <Press momentarily> | → | LPF∗ |
|
| <Press momentarily> |
|
| ||
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
|
| <Press for at least 2 seconds> |
|
| normal mode ← |
| ||||||
|
|
|
|
|
∗When the subwoofer output of this unit is turned OFF, LPF and phase are deactivated.
2 Press the DN g or f UP button to select the desired setting.
1.HPF (Setting the High Pass Filter):
FLAT (OFF) ←→ 80Hz ←→ 120Hz ←→ 160Hz
Outputs all frequencies higher than that selected according to your preference.
2.LPF (Setting the Low Pass Filter):
FLAT (OFF) ←→ 80Hz ←→ 120Hz ←→ 160Hz