Turning Subwoofer ON/OFF

When the subwoofer is on, you can adjust the subwoofer output level (refer to page 19).

For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected.

1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode.

2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW mode, and then press /ENTER.

SUBW SUBW SYSTEM* BASS TREBLE HPF SUBW

* Displayed only when subwoofer is ON.

3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select SUBW ON/OFF, and then press /ENTER.

ON OFF

4 Press to return to normal mode.

•If no operation is performed for 15 seconds, the unit will return to normal mode automatically.

•If is pressed during setting, the unit returns to the previous item.

Setting the Subwoofer System

When the subwoofer is on, you can select either SYS 1 or SYS 2 for the desired subwoofer effect.

For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected.

1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode.

2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW SYSTEM mode, and then press /ENTER.

SUBW SUBW SYSTEM* BASS TREBLE HPF SUBW

* Displayed only when subwoofer is ON.

3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the SUBW SYS 1 or SUBW SYS 2, and then press

/ENTER.

SYS 1 SYS 2

4 Press to return to normal mode.

•If no operation is performed for 15 seconds, the unit will return to normal mode automatically.

•If is pressed during setting, the unit returns to the previous item.

•This function is inoperable when Subwoofer is set to OFF.

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal preference.

For iDA-X200, the following setting can be made only when the IMPRINT audio processor (PXA-H100) is not connected.

1 Press and hold IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only) for at least 2 seconds to activate the AUDIO selection mode.

2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the BASS Adjustment mode, and then press

/ENTER.

SUBW SUB SYSTEM* BASS TREBLE HPF SUBW

* Displayed only when subwoofer is ON.

Setting the Bass Level

3-1*1Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass level (–7~+7), and then press

/ENTER.

You can emphasize or weaken the bass level.

Setting the Bass Bandwidth

3-2 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass bandwidth, and then press /ENTER.

Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the center frequency. A narrower setting will boost only frequencies near the center frequency.

Setting the Bass Center Frequency

3-3 Turn the Double Action encoder (iDA-X200 only) or Rotary encoder (iDA-X300 only) to select the desired bass center frequency, and then press

/ENTER.

80(Hz) 100(Hz) 200(Hz) 60(Hz) 80(Hz)

Emphasizes the displayed bass frequency ranges.

4 Press to return to normal mode.

•If no operation is performed for 15 seconds, the unit will return to normal mode automatically.

•If is pressed during setting, the unit returns to the previous item.

•The function is inoperable when DEFEAT is set to ON.

*1 The adjustment can also be made by pressing IMPRINT (iDA-X200 only) or SOUND (iDA-X300 only). Refer to “Adjusting Subwoofer/ Bass/Treble/Balance(Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat” (page 19).

20-EN