BASIC OPERATIONS (CONT.)
played more than once. To create a program:
1)Be sure a disc is inserted in the drive and press the PROGRAM BUTTON (3). Pressing the PROGRAM BUTTON (3) from any function will immediately pause the disc and go into program mode.
2)After pressing the PROGRAM BUTTON (3) to activate the units program mode the program indicator LED above the PROGRAM BUTTON (3) will light and the PROGRAM INDICATOR (33) in the LCD DISPLAY (21) will glow indicating that PROGRAM MODE has been activated.
3)Select a track to be programmed by using the FWD SKIP and BACK SKIP TRACK BUTTON (11 & 15).
4)Once you reach the track you wish to place in to the program memory pressing PROGRAM BUTTON (3) will lock the track into memory.
5)Repeat these steps up to 19 times (ie. up to 20 tracks can be programmed).
6)As you program tracks in memory the LCD DISPLAY (21) will indicate which tracks have been programmed.
7)When you have finished your programming and are ready to begin playback simply press the PLAY BUTTON
(9) and your program will begin to play.
8)After you have complete your program you can always add more tracks to your program by repeating the steps above. Remember that you can only a maximum of 20 track in a program and you can only add track not subtract.
9)To cancel and clear the program press and hold down the PROGRAM BUTTON (3) for more than two seconds.
15. SETTING And STORING A CUE POINT:
A cue point is a starting point for a song. You may set a cue point anywhere in a disc or track.You may set up to seven independent cue points per disk. Six cue points are stored in the CUE BUTTONS
There are two (2) ways to set a CUE point:
1)You may press the IN R./CUE BUTTON (12) on the fly (while the disc is playing). This will set a CUE Point without music interruption. Pressing the CUE BUTTON (10) will now return you to the same point that you pressed the IN R./CUE BUTTON (12). You may now store this CUE Point in any of the CUE BUTTONS
(2). Pressing the cue button or the IN R./CUE BUTTON (12) will now return you to this exact point.
2)You may also use the JOG SHUTTLE (8) to set a cue point. While a disc is in PAUSE or CUE mode, use the JOG WHEEL (7) to scroll through a track to find your desired starting point. Once you have found your desired position press the PLAY BUTTON (9) to set your cue point. Pressing the cue button or the IN R./CUE BUTTON (12) will now return you to this exact point.
Storing A Cue Point:
Once you have set your CUE Point by one of the two means listed above you may store your cue point in one of the CUE BUTTONS (2). Once you store this cue point in memory you may recall it at any time and you may even recall if the disc has been remove or power had been disconnected. You may store a maximum of six cue points per a disc and maximum of 40 cue points can saved in drives memory. The MEMORY BUCKET (42) on the LCD DISPLAY (21) will remind you how much memory is available.
To Store a cue point:
1)Press the MEMORY CUE BUTTON (1), the red Memory Cue LED will glow indicating that memory is ready to be set. You may now press any one of the six (6) CUE BUTTONS (2) to store your cue point into memory. After pressing one of the CUE BUTTONS (2), the LED to cue button you selected will flash briefly and remain lit indicating memory has been set. The red Memory Cue LED will now shut off.
2)Repeat the above steps to store up to six (6) Cue Points per a disc. Once all your six (6) cue points have been stored you may access them at any time. The cue points will instantly start without any interruption of music. Please note in order to access these cue point the disc that created the cue points from must be in the player. must have the same CD in the tray to Play them.
3)Remember that either a CUE POINT or a SAMPLE LOOP can be stored into a CUE BUTTON (2), not both. A cue point will be indicated by glowing red CUE BUTTON (2) and sample will be indicated by a MEMORY NUMBER (41) in the LCD DISPLAY (21).
American DJ® AUDIO • PRO DJ3™ INSTRUCTION MANUAL • PAGE 13
