Rev 1 |
| |||
|
|
|
| |
Test Relay Enable {1} |
| This parameter must be set to “Enable” to permit the eight | Test Relay En m+ | |
[SYSTEM/DIAG] |
| output relays to be manually tested; otherwise, the state of the | Disable |
|
|
| relays will be per system conditions. |
|
|
|
|
|
|
|
Test Relay 1 {1} |
| Setting this parameter to “ON” energizes Relay 1 and turns | Test Relay 1 | m+ |
[SYSTEM/DIAG] |
| on the “ALM1” LED on the control unit front panel. | OFF |
|
|
|
|
| |
|
|
|
|
|
• |
| • | • |
|
• |
| • | • |
|
• |
| • | • |
|
|
|
|
|
|
Test Relay 6 {1} |
| Setting this parameter to “ON” energizes Relay 6 and turns | Test Relay 6 | m+ |
[SYSTEM/DIAG] |
| on the “ALM6” LED on the control unit front panel. | OFF |
|
|
|
|
| |
|
|
|
|
|
Test Minor Relay {1} |
| Setting this parameter to “ON” energizes the Minor Relay | Test Min Rly | m+ |
[SYSTEM/DIAG] |
| and turns on the “MIN” LED on the control unit front panel. | OFF | |
|
|
| ||
|
|
|
|
|
Test Major Relay {1} |
| Setting this parameter to “ON” de | Test Maj Rly | m+ |
[SYSTEM/DIAG] |
| and turns on the “MAJ” LED on the control unit front panel. | OFF | |
|
|
| ||
|
|
|
|
|
BATTERY SETUP |
|
|
|
|
|
|
|
|
|
Float Voltage {1} |
| Float voltage at 25°C bat tery temperature. | Batt Float | m+ |
[BATT/PARAM] |
|
| 27.00 V | |
|
|
| ||
|
|
|
| |
Maximum Recharge Current | {1} | Maximum battery recharge current (the system limits the | Batt Max Rech m+ | |
[BATT/PARAM] |
| charging current to this programmable value). | 100A | |
|
|
| ||
|
|
|
|
|
Compensation Method {1} |
| Activate “000001” or de | Comp Method | m+ |
[BATT/COMP] |
| temperature compensation. | 000000 |
|
|
|
|
| |
|
|
|
|
|
Temperature Compensation | {1} | Temperature compensation between low knee and high knee | Comp TC | m+ |
[BATT/COMP] |
| in mV/cell/°C. (Compensation equals zero at 25°C.) | - 3.00mV | |
|
|
| ||
|
|
|
| |
Compensation High Knee {1} | The temperature compensation high knee is the point above | Comp Hknee | m+ | |
[BATT/COMP] |
| which there is no additional battery voltage compensation for | 40.0 C | |
|
| further increases in temperature. | ||
|
|
|
| |
|
|
|
| |
Compensation Low Knee {1} | The temperature compensation low knee is the point below | Comp Lknee | m+ | |
[BATT/COMP] |
| which there is no additional battery voltage compensation for | 0.0 C | |
|
| further decreases in temperature. | ||
|
|
|
| |
|
|
|
| |
Discharge Threshold {1} |
| An alarm is generated if the battery discharge current exceeds | Batt Disc Thr m+ | |
| this value. | 100 A | ||
|
|
| ||
|
|
|
|
|
High Voltage Threshold {1} |
| An alarm is generated if the magnitude of the battery voltage | Batt HV Thr | m+ |
| rises above this value. | 28.00 V | ||
|
|
| ||
|
|
|
|
|
Low Voltage Threshold {1} |
| An alarm is generated if the magnitude of the battery voltage | Batt LV Thr | m+ |
| drops below this value. | 22.00 V | ||
|
|
| ||
|
|
|
| |
High Temperature Threshold {1} | An alarm is generated if the battery temperature exceeds this | Batt HT Thr | m+ | |
| value. | 70.0 C | ||
|
|
| ||
|
|
|
|
|
Low Temperature Threshold | {1} | An alarm is generated if the battery temperature drops be low | Batt LT Thr | m+ |
| this value. | 0.0 C | ||
|
|
| ||
|
|
|
|
|
37
