American Standard 2083 SERIES installation instructions

STANDARD®

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2083 SERIES BATHING POOL

INSTALLATION INSTRUCTIONS

60"

7-3/4"

(1524mm)

3/4"

(197mm)

FINISHED

70mm

(19mm)

WALL

(2-3/4)

4"

15-3/8"

(391mm)

(102mm)

229mm x 305mm

(9 x 12)

FLOOR

4"

(102mm)

CUTOUT

32"

(813mm)

2-3/8"

+13mm

(2-3/8)

+(1/2)

C/L OF 1/2

25mm

4-1/2"

(1) C/L OF

(114mm)

SUPPLIES

DRAIN

AS REQ'D

SHOWER ARM- 1/2 N.P.T.

1-1/4"(32mm) DIA. HOLE

C/L OF CURTAIN ROD

USUALLY 76"(1930mm) FROM

FINISHED FLOOR

					FINISHED
	C/L OF	(2) 2-1/8"(54mm)		4"	WALL
	VALVES			(102mm)
		DIA. HOLES
OPTIONAL		4"	4"	SPOUT-
TO FLOOR
	16"	(102mm)	(102mm)	1/2 N.P.T.
USUALLY
BETWEEN	(406mm16)			3-1/2"
65 & 78				(89mm)
(1651 & 1981mm)		1"
	(25mm)				SEE	19-3/4"
	20"
					NOTE
						(502mm)
	(508mm)
TOP OF DECK
					2"
					(51mm)
						ROUGH
		4-5/8"				FLOOR
				1-1/2 N.P.T. THREADS
		(117mm)
				1-1/2 O.D. TAILPIECE

BATH SUPPORT MATERIAL

GENERAL SPECIFICATIONS FOR 2083 BATHING POOL

INSTALLED SIZE			60 x 32 x 20 In.
		(1524 x 813 x 508mm)
WEIGHT				100 Lbs. (45 Kg.)
WEIGHT w/WATER			551 Lbs. (250 Kg.)
GAL. TO OVERFLOW				54 Gal. (204 L)
BATHING WELL AT SUMP		18 x 42 In. (457 x 1067mm)
BATHING WELL AT RIM		25 X 54 In. (635 x 1372mm)
WATER DEPTH TO OVERFLOW				14 In. (356mm)
FLOOR LOADING	41 Lbs./Sq.Ft. (202 Kgs./Sq.m)
(PROJECTED AREA)
PTS.						20.8
CUBE (FT3)					35.3

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. All you need to finish the installation are your selected fittings.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

• Standard Bath Caddie 9533.100*

*see your American Standard Distributor

List of Required Components (not included):

•Standard Bath Drain 1501.170*

•Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulk
•	Slip Joint Pliers		(waterproof)
•	Screw Driver	•	1 x 3 or 2 x 4
•	Standard		Stringers
	Woodworking Tools	•	Drop Cloth
•	Personal Safety	•	Mortar Mix
	Equipment		or Grout
•	Caulking Gun

GENERAL INSTALLATION INFORMATION

BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.

Locate studs as required. Insure rough dimensions are proper, plumb, and square. The following procedure must be used for all installations: Leveling support stringer should be as indicated. This bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout.

Position bathtub within the recess, check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use drywall screws with flatwashers or roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4" drywall screws and flatwashers.

SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.

CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH. The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© AS America, Inc. 2008

753450-100 REV. BAll product names listed herein are trademarks of AS America, Inc. unless otherwise noted.