American Standard 2383, 2371, 2466, 2351 manual List of Required Tools and Supplies, Specifications

General Installation Information

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard, tile, etc., the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling! Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system. Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others.

For electrical requirements, refer to section titled “Whirlpool Electrical Installation Instructions”. Check for availability of optional American Standard wall tiling bead (required for recess installation). Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

!WARNING: Do not lift whirlpool by the piping harness at any time.

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
• Tape Measure		• Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 4 Stringers
•	Screw Driver	•	Drop Cloth
•	Standard Woodworking Tools	•	Cement, Plaster, Grout

•Personal Safety Equipment

•Caulking Gun

LIST OF OPTIONAL COMPONENTS (NOT INCLUDED):

DESCRIPTION	MODEL #	OPTIONAL COMPONENTS (NOT INCLUDED)
		E-Z INSTALL HEATER	APRON KIT	TILE BEAD KIT
CORNER DUET WITH SEAT	51	EZHEAT-100	N/A	751755-100
CENTURION ' X "	71	EZHEAT-100	N/A	751755-100
CONTEMPO OVAL		EZHEAT-100	N/A	N/A
FREE SPIRIT ' X 54"	4	EZHEAT-100	N/A	751755-100

• For these components please see your Vendor.

SPECIFICATIONS:

L

SIDE VIEW

W

H

END VIEW

J

CA

BDRAIN / OVERFLOW

TABLE 1: GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS

Description	Dimensions	Drain / Overflow	Height to	Cut Out Pier	Rough-In Recess	Tub Edge to
			Underside of Deck:			Centerline Overflow:
	L-W-H			G x F	E x D
			C			J
51	L 4-1/" (14mm)	A 1-/"	C 1"	See Pier	N/A	1-5/"
		(40 mm)
Corner	W 0-1/" (157mm)		(4 mm)
		B 4"		Cutout		(1mm)
	H 0-1/" (51mm)
		(10 mm)		Dimensions
71	L 7" (1mm)	A 15-1/"	C 0-1/4"	70-1/"	7-/1"	"
		(4 mm)		(171 mm)	(1 mm)
' x "	W " (14mm)		(514 mm)
		B 10"		x 4-1/"	x 4-1/"	(15mm)
	H 1-/4" (55mm)
		(54 mm)		(7 mm)	(7 mm)
	L 7" (1mm)	A 1-1/"	C "	See Pier		-1/4"
		(470 mm)		Cutout	N/A
Oval	W 4" (107mm)		(54 mm)			(10mm)
	H 5-1/" (4mm)	B 15-/4"		Dimensions
		(400 mm)
4	L 7" (1mm)	A 17"	C 1-/4"	70-1/"	7-/1"
		(4 mm)		(171 mm)	(1 mm)
' x 54"	W 54" (17mm)		(55 mm)			N/A
		B "		x 5"	x 5-1/"
	H -1/4" (51mm)
		(14 mm)		(14 mm)	(14 mm)

754407-100 Rev. B