1

WASHSTAND ASSEMBLY

Back Front

Thread the two legs with tapered upper ends into the threaded holes at the front of the cabinet. Thread the remaining legs into the two holes at the rear of the cabinet. Hand-tighten each of the four legs.

2

SINK AND WASHSTAND INSTALLATION

Note: If replacing an existing sink be certain to shut off water supply before removing old sink. If installing in a new bathroom follow rough-in diagram to locate rough supply, waste lines.

Provide suitable reinforcement behind finished wall for sink hanger screws. For an installed sink height of 36", center the reinforcement 29" above the floor.

C/L of 2 x 8

Support

and Bracket

29"

Finished

Floor

31) Move washstand into approximate position near the wall.

2)Place sink on washstand, aligning the tapered ends of the front legs with the recesses in the underside of the front of the sink.

3)Place a level on the cabinet and use the four independently adjustable washstand feet to level the assembly both side-to-side and front-to-back.

4)Place the level on the sink. If adjustment is required, either front-to-back or side-to-side, remove the sink, place one or more of the adhesive-backed cushions on the top surfaces of any of the legs as appropriate, and replace the sink to verify.

5)Move the assembly into contact with the wall.

6)With a pencil, mark through the center of the two mounting holes found on the back of the sink. See VIEW "A".

7)Move the assembly well clear of the wall.

8)Drill two pilot holes at the center marks using a 1/4" bit. Bore in 1" deep.

9)Thread the two 5/16" headless hanger screws into the pilot holes leaving 1-7/8" thread exposed in front of the wall.

With lavatory in place mark the two mounting hole locations.

VIEW "A"

VIEW "A"

Feet are adjustable

4

Following manufacturer's instructions, install faucet and drain assembly (not included) in sink. Be certain to apply a bead of sealing putty on the underside of the drain to ensure a watertight seal between the sink and the drain. Remove excess putty immediately after tightening drain.

Move the assembly back toward the wall, guiding the sink over the two headless hanger screws. Place washers over studs and firmly hand-tighten nuts onto each.

Lavatory

Front Leg

Hanger Screw,

of Washstand

Washer & Nut

- 2 -

7 3 0 8 0 4 - 1 0 0

Page 2
Image 2
American Standard 9422.020 installation instructions Washstand Assembly, Sink and Washstand Installation

9422.020 specifications

The American Standard 9422.020 is a well-regarded bathroom fixture that has gained popularity for its blend of functionality, efficiency, and modern design. This model features a sleek, minimalist look that complements various bathroom styles, making it a versatile choice for both contemporary and traditional settings.

One of the standout characteristics of the American Standard 9422.020 is its integrated flush valve technology. This feature is designed to ensure a powerful and efficient flush while using minimal water, which helps conserve resources and reduce utility bills. The high-efficiency design boasts a 1.28 gallons per flush (GPF) rating. This not only promotes sustainability but also meets the standards set by the Environmental Protection Agency’s WaterSense program, enhancing its appeal for environmentally-conscious consumers.

The toilet is crafted from vitreous china, a robust material known for its durability and ease of cleaning. It features a smooth, high-gloss finish that withstands stains and scratches, ensuring that the toilet remains visually appealing even after years of use. The toilet’s bowl is elongated, which provides additional comfort for the user, making it a preferred choice for many households.

Another significant highlight of the American Standard 9422.020 is its EverClean surface. This innovative coating inhibits the growth of bacteria, mold, and mildew on the surface of the toilet, enhancing hygiene and reducing the need for harsh cleaning products. This feature not only contributes to a cleaner bathroom environment but also extends the lifespan of the toilet.

Installation is made straightforward with the American Standard 9422.020, thanks to its standard sizing and mounting options. This makes it a practical choice for both DIY enthusiasts and professional plumbers alike. Furthermore, the toilet tank is designed to be quiet, minimizing noise disruption in the bathroom.

In summary, the American Standard 9422.020 combines elegant design with advanced technologies to deliver an efficient, comfortable, and eco-friendly toilet solution. Its modern features and durable construction make it a reliable choice for homeowners looking to upgrade their bathrooms or build new ones.