Analog Devices AD8342 specifications Lo Considerations

	+V
	S
AD8342
COMM	8
	2:1
IFOP	7
IFOM	6

COMM 5 ZL = 100Ω

IF OUT
Z	O	= 50Ω
		05352-047

		AD8342
	30
	25	MODELED
GAIN (dB)	20
	15	MEASURED
VOLTAGE

Figure 47. Biasing the IF Port Open-Collector Outputs

Using a Center-Tapped Impedance Transformer

+VS

10

5

057

AD8342

COMM 8

IFOP 7

IFOM 6

COMM 5

RFC

			IF OUT+
Z	L	=	100Ω
			IF OUT–

RFC

+VS

IMPEDANCE		ZL
TRANSFORMING
NETWORK
	05352-048

0			05352-
	100	1000
10
	IF LOAD (Ω)

Figure 49. Voltage Conversion Gain vs. IF Loading

LO CONSIDERATIONS

The LOIN port provides a 50 Ω load impedance with common- mode decoupling on LOCM. Again, common-grade ceramic

Figure 48. Biasing the IF Port Open-Collector Outputs

Using Pull-Up Choke Inductors

The AD8342 is optimized for driving a 100 Ω load. Although the device is capable of driving a wide variety of loads, to main- tain optimum distortion and noise performance, it is advised that the presented load at the IF outputs is close to 100 Ω. The linear differential voltage conversion gain of the mixer can be modeled as

Av = Gm ⋅ RLOAD

where:
Gm	=	1	gm
		π 1	+ gm Re

RLOAD is the single-ended load impedance.

gm is the transistor transconductance and is equal to 1810/RBIAS.

Re is 15 Ω.

The external RBIAS resistor is used to control the power dissipa- tion and dynamic range of the AD8342. Because the AD8342 has internal resistive degeneration, the conversion gain is pri- marily determined by the load impedance and the on-chip degeneration resistors. Figure 49 shows how gain varies with IF load. The external RBIAS resistor has only a small effect. The most direct way to affect conversion gain is by varying the load impedance. Small loads result in lower gains while larger loads increase the conversion gain. If the IF load impedance is too large it causes a decrease in linearity (P1dB, IP3). In order to maintain positive conversion gain and preserve SFDR perform- ance, the differential load presented at the IF port should remain in the range of ~ 100 Ω to 250 Ω.

capacitors provide sufficient signal coupling and bypassing of the LO interface.

The LO signal needs to have adequate phase noise characteris- tics and low second-harmonic content to prevent degradation of the noise figure performance of the AD8342. An LO plagued with poor phase noise can result in reciprocal mixing, a mecha- nism that causes spectral spreading of the downconverted sig- nal, limiting the sensitivity of the mixer at frequencies close-in to any large input signals. The internal LO buffer provides enough gain to hard-limit the input LO and provide fast switch- ing of the mixer core. Odd harmonic content present on the LO drive signal should not impact mixer performance; however, even-order harmonics cause the mixer core to commutate in an unbalanced manner, potentially degrading noise performance. Simple lumped element low-pass filtering can be applied to help reject the harmonic content of a given local oscillator, as shown in Figure 50. The filter depicted is a common 3-pole Chebyshev, designed to maintain a 1-to-1 source-to-load impedance ratio with no more than 0.5 dB of ripple in the pass band. Other filter structures can be effective as long as the second harmonic of the LO is filtered to negligible levels, for example, ~30 dB below the fundamental.

AD8342

LOCM LOIN COMM

RS

2

3

4

L2

LO

SOURCE

C1

C3

RL

FOR RS = RL

C1 =

1.864

L2 =

1.28RL

C3 =

1.834

2πf

c

R

L

2πf

c

2πf

c

R

L

fC - FILTER CUTOFF FREQUENCY

05352050-

Figure 50. Using a Low-Pass Filter to Reduce LO Second Harmonic

Rev. 0 Page 17 of 20