AOC CT700G user manual signal′ 15-pincableconnector, CT740gPlugonlyaudiocabl, CT740gPlugonlyDC

Plug & Play DDC1/2B Feature

TECHNICAL SUPPORT(FAQ)

This monitor is equipped with

VESA

DDC1/2BPower LED is not on

INSTALLATION INSTRUCTIONS

according to the VESA DDC STANDARD. It allows

*Power Cord should be connected

SWIVEL BASE

inform the host system of its identity and,

No Plug & Play

To attach the swivel base to the monitor, do th

of DDC used, communicate additional information

∙ Carefully turn the monitor on its side or ups

*Check if the PC System is Plug & Play

capabilities. The communication

channel

is

compatible

*Check if the Video Card is Plug & Play

(see figure 1)

compatible

DDC1 and DDC2B.

∙ Locate the cavities at the bottom front of th

*Check if the D-15 plug pin of Video Cable is bent

The DDC1 is a unidirectional data channel from

∙ Insert the pegs on the swivel base into these

*Make sure the AOC Monitor Drivers are installed

host that continuously transmits EDID information

swivel base forward until the swivel base lock

(AOC

Monitor Drivers are

availableat:

∙ To remove the swivel base, hold the bottom of

a bidirectional data channel based on the I†Cwww.aocmonitor.com)

then push it out.

can request EDID information over the DDC2B

Picture is fuzzy

POWER CORD

*Adjust the Contrast and Brightness Controls.

THIS MONITOR

WILL APPEAR TO BE

NON-FUNCTIONAL

Power Source:

Picture bounces or a wave pattern is

the correct

typ

1. Make sure the power cord is

THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FORpicture

your area.

MONITOR TO OPERATE

PROPERLY,

THERE

MUST BE

A

electricales devicthat

may

cause

2. This monitor has a universal

power supply

th

VIDEO INPUT SIGNAL.

*Move

interference.

in either 100/120V

AC or 220/240V

AC voltage

This monitor

meets the

Green Monitor standards

as set

by the

adjustment is required).

Video Electronics Standards Association (VESA)

The power

LED is

ON (orange)

but ther

3. Connect the power cord into your monitor￿s p

States Environmental

Protection

Agency

(EPA)

no picture.

and then plug the other end into a 3-pin AC

Confederation

Employees (

NUTEK

*Computer Power Switch should be in the ON position.

). This feature

is designed to

power cord may be connected to either a wall

conserve electrical energy

by

reducing

power

*Computer Video Card should be snugly seated in its slot.

consumption when

the power outlet socket

on your PC, dependin

*Make sure monitor￿s videopropercablye conneis

power cord supplied with your monitor.

there is no video input signal present. When there is no video input

signal this monitor,

following

the computer.

VIDEO CABLE

a time-out period, will

automatically

switch to an OFF mode. This reduces

*Inspect monitor￿s video cable and mak

Connecting

the VideotheCable:monitor

comes with

a b

the monitor’s internal power

supply consumption. After

the

video

pins are bent.

full

video cable. Plug

the

signal′ 15-pincableconnector

int

input signal is

restored,

power is restored and

the

*Make sure computer is operational by

computer’s

video

port

and

tighten the two

scr

display is automatically

redrawn. The

appearance is

similar

to

a "Screen

LOCK key on the keyboard while obse

connector. (see figure 2)

Saver" feature

except the

LOCK LED. The LED should eitherOFFturna ON o

display is completely off. The display is restored by pressing a key

Caution:Don￿t bend the signal cable, otherwise i

on the keyboard, or clicking the mouse.

hitting the CAPS LOCK key.

inner wire.

USING THE RIGHT POWER CORD:

Missing one of the primary colors (R

Connecting

the Power PlugCord:the

power

cord

int

The accessory power cord for the Northern

BLUE)

monitor’s

AC power jack.

Then

plug

the powe

wallet plug with NEMA 5-15 style and is UL*Inspect the monitor￿s video cable and

grounded

AC outlet, UL-approved power strip,

labeled. The

voltage

rating for

the power

of the pins are

bent.

output socket on your PC.

AC.

Caution:If

the AC

outlet is not

grounded,

ins

grounding adapter (not supplied).

Supplied with

units

intended

for

connection

to

power outlet of

Connecting

the Audio

Cable

( CT740gPlugonlyaudio):cabl

personal computer: Please use a cord set consisting of a minimum

between the computer

multi-media

(or

sound) car

No. 18 AWG, type SJT or SVT three conductors flexible cord. One

and monitor’s audio input.

end terminates with a grounding type attachment plug, rated 10A,

Connecting

the DC Power Cable

(

CT740gPlugonlyDC )

250V, CEE-22 male configuration. The other end terminates with a	power cable between monitor to swivel base for
molded-on type connector body, rated 10A, 250V, having standard
CEE-22 female configuration.

4