PROTECT YOUR MODEL, YOURSELF

&OTHERS...FOLLOW THESE IMPORTANT SAFETY PRECAUTIONS

1.Your EP Zero ARF should not be considered a toy, but rather a sophisticated, working model that functions very much like a full-size airplane. Because of its performance capabilities, the EP Zero ARF, if not assembled and operated correctly, could possibly cause injury to yourself or spectators and damage to property.

2.You must assemble the model according to the instructions. Do not alter or modify the model, as doing so may result in an unsafe or unflyable model. In a few cases the instructions may differ slightly from the photos. In those instances the written instructions should be considered as correct.

3.You must take time to build straight, true and strong.

4.You must use an R/C radio system that is in first-class condition, and a correctly sized motor and components (ESC, wheels, etc.) throughout the building process.

5.You must correctly install all R/C and other components so that the model operates correctly on the ground and in the air.

6.You must check the operation of the model before every flight to insure that all equipment is operating and that the model has remained structurally sound. Be sure to check clevises or other connectors often and replace them if they show any signs of wear or fatigue.

7.If you are not an experienced pilot or have not flown this type of model before, we recommend that you get the assistance of an experienced pilot in your R/C club for your first flights. If you’re not a member of a club, your local hobby shop has information about clubs in your area whose membership includes experienced pilots.

8.While this kit has been flight tested to exceed normal use, if the plane will be used for extremely high-stress flying, such as racing, or if an motor larger than one in the recommended range is used, the modeler is responsible for taking steps to reinforce the high-stress points and/or substituting hardware more suitable for the increased stress.

We, as the kit manufacturer, provide you with a top quality, thoroughly tested kit and instructions, but ultimately the quality and flyability of your finished model depends on how you build it; therefore, we cannot in any way guarantee the performance of your completed model, and no representations are expressed or implied as to the performance or safety of your completed model.

Remember: Take your time and follow the instructions to end up with a well-built model that is straight and true.

LITHIUM BATTERY HANDLING & USAGE

WARNING!! Failure to follow all instructions could cause permanent damage to the battery and its surroundings, and cause bodily harm!

ONLY use a LiPo approved charger. NEVER use a NiCd/NiMH peak charger!

NEVER charge in excess of 4.20V per cell.

ONLY charge through the “charge” lead. NEVER charge through the “discharge” lead.

NEVER charge at currents greater than 1C.

ALWAYS set charger’s output volts to match battery volts.

ALWAYS charge in a fireproof location.

NEVER trickle charge.

NEVER allow the battery temperature to exceed 50°F (65°C).

NEVER disassemble or modify pack wiring in any way or puncture cells.

NEVER discharge below 2.5V per cell.

NEVER place on combustible materials or leave unattended during charge or discharge.

ALWAYS KEEP OUT OF REACH OF CHILDREN.

DECISIONS YOU MUST MAKE

In the hands of a capable pilot the EP Zero ARF is an impressive 3D performer. But for the EP Zero ARF to perform to its full potential, it must be properly equipped with all the right gear (servos, batteries, receiver, and speed control). There may be more than one type and brand of radio equipment that can be used, but based on extensive testing, following is the equipment we recommend so you can get the most performance out of your EP Zero ARF and assemble it as shown in this instruction manual.

Transmitter

With a standard, four-channel radio the EP Zero ARF is capable of all the basic 3D maneuvers. However, some advanced pilots who are already familiar with handling “foamies” may prefer to fly the EP Zero ARF with a computer radio capable of endpoint adjustments (for fine-tuning control throws), exponentials (for “softening” the throws near the center of the travel), and various mixing functions (such as rudder-to-elevator mixing for extended knife-edge flight).

Servos

The EP Zero ARF requires three micro servos with a minimum torque rating of 15 oz-in. Futaba® S-3108 micro servos (FUTM0042) are ideal because they meet the torque and weight requirements. Although there may be other servos that will physically fit in the model, those outside the recommended

3

Page 3
Image 3
APC EP Zero ARF Protect Your MODEL, Yourself, Lithium Battery Handling & Usage, Decisions YOU Must Make, Transmitter