Manuals
/
Arkon
/
Household Appliance
/
Water System
Arkon
Channelmag ChannelMag Junction Box Wiring Diagram, ChannelMag Installation, Red Or Clear
Models:
Channelmag
1
20
25
25
Download
25 pages
15.23 Kb
17
18
19
20
21
22
23
24
<
>
Install
ChannelMag Junction Box Wiring Diagram
Dimension
Maintenance
Transmitter Fault 4.7 All Checks Good, But No Signal
Weight
Safety
Page 20
Image 20
ChannelMag
Section 2 Installation
2.6.1 ChannelMag Junction Box Wiring Diagram
BLACK
RED OR CLEAR
SHIELD
ChannelMag
Section 2 Installation
CAUTION
20
Page 19
Page 21
Page 20
Image 20
Page 19
Page 21
Contents
RTM- Expolink s.r.o., Prikop 8, 60200 Brno, Czech Republic
CHANNELMAG FLOWMETERS
FOR OPEN CHANNELS AND NON- FULL PIPES
Instruction Manual
FOREWORD
Email office@rtm-expolink.com
IMPORTANT - PLEASE READ
DANGER
DANGER
Table of Contents
Section 2 Installation
Section 4 Maintenance
ChannelMag
Section 5 Recommended Spares
Table of Contents
Erratic Signal
Signal or Indication “Swing”
ChannelMag
Section 1 Introduction
1.1 Scope ChannelMag CM2
1.2 Scope ChannelMag PM2
Chanel Mag Section I Introduccion
1.3 Safety
DANGER
Section 2 Installation
2.1 Media Considerations
2.1 Location and Mounting
ChannelMag
2.3.2 Straight Lengths of Pipe PM2
2.3. Straight Lengths of Channel / Pipe
2.3.1 Straight Lengths of Channel CM2
2.4 Installation, Dimensions and Approx. Weights 2.4.1 CM2 Sensors
2.3.3 Important Note
Weight
Nominal
Cables from each sensor are to run in separate conduits to the
2.4.2 Installation of 2 x CM2 ChannelMag Sensors
2.4.3 CM2/D Dimensions and
Approximate Weight
2.4.4 PM2 Sensors in Full Pipes
Note CM2/8” ChannelMag sensors are normally supplied with ramps
2.4.5 PM2 Sensors in Non-Full Pipes
Partially Filled Pipes -- Single Sensor
2.4.6 Installation of PM2 Sensors With Magnetic Enhancement Band
Center spacer used for compound sensor installation only
ChannelMag Section 2 Installation
Outer mounting points used without center spacer
2.5 Grounding
2.4.8 ChannelMag PM2 Weights and Dimensions
2.4.7 ChannelMag PM2 Enhancement Plate Expander Mechanism
2.6 Cable Types
2.6.1 ChannelMag Junction Box Wiring Diagram
ChannelMag Section 2 Installation
ChannelMag Section 2 Installation
RED OR CLEAR
2.6.2 ChannelMag Entela Approval 2.7 Cable Runs From The Junction Box
3.1 Calibration and Range Factors
Section 4 Maintenance
4.1 Cleaning 4.2 Zero Span Checking
4.3 Effect of Moisture Ingression
4.4 Effect of a Grounded Electrode
4.6 Transmitter Fault 4.7 All Checks Good, But No Signal
4.8 Erratic Signal
4.9 Signal Or Indication “Swing”
ChannelMag Section 4 Maintenance
ChannelMag
Section 5 Recommended Spares
5.1 Recommended Spares