Manuals
/
Arkon
/
Household Appliance
/
Water System
Arkon
Channelmag instruction manual Recommended Spares, Table of Contents, Erratic Signal, 2525
Models:
Channelmag
1
5
25
25
Download
25 pages
15.23 Kb
1
2
3
4
5
6
7
8
<
>
Install
ChannelMag Junction Box Wiring Diagram
Dimension
Maintenance
Transmitter Fault 4.7 All Checks Good, But No Signal
Weight
Safety
Page 5
Image 5
Table of Contents
4.8
Erratic Signal
24
24
4.9
Signal or Indication “Swing”
24
24
Section 5 Recommended Spares
5.1 Recommended Spares
2525
5
Page 4
Page 6
Page 5
Image 5
Page 4
Page 6
Contents
CHANNELMAG FLOWMETERS
RTM- Expolink s.r.o., Prikop 8, 60200 Brno, Czech Republic
FOR OPEN CHANNELS AND NON- FULL PIPES
Instruction Manual
Email office@rtm-expolink.com
FOREWORD
IMPORTANT - PLEASE READ
DANGER
DANGER
Section 2 Installation
Table of Contents
Section 4 Maintenance
ChannelMag
Table of Contents
Section 5 Recommended Spares
Erratic Signal
Signal or Indication “Swing”
ChannelMag
Section 1 Introduction
1.1 Scope ChannelMag CM2
Chanel Mag Section I Introduccion
1.2 Scope ChannelMag PM2
DANGER
1.3 Safety
2.1 Media Considerations
Section 2 Installation
2.1 Location and Mounting
ChannelMag
2.3.2 Straight Lengths of Pipe PM2
2.3. Straight Lengths of Channel / Pipe
2.3.1 Straight Lengths of Channel CM2
2.3.3 Important Note
2.4 Installation, Dimensions and Approx. Weights 2.4.1 CM2 Sensors
Weight
Nominal
Cables from each sensor are to run in separate conduits to the
2.4.2 Installation of 2 x CM2 ChannelMag Sensors
Approximate Weight
2.4.3 CM2/D Dimensions and
Note CM2/8” ChannelMag sensors are normally supplied with ramps
2.4.4 PM2 Sensors in Full Pipes
Partially Filled Pipes -- Single Sensor
2.4.5 PM2 Sensors in Non-Full Pipes
Center spacer used for compound sensor installation only
2.4.6 Installation of PM2 Sensors With Magnetic Enhancement Band
ChannelMag Section 2 Installation
Outer mounting points used without center spacer
2.5 Grounding
2.4.8 ChannelMag PM2 Weights and Dimensions
2.4.7 ChannelMag PM2 Enhancement Plate Expander Mechanism
2.6 Cable Types
ChannelMag Section 2 Installation
2.6.1 ChannelMag Junction Box Wiring Diagram
ChannelMag Section 2 Installation
RED OR CLEAR
2.6.2 ChannelMag Entela Approval 2.7 Cable Runs From The Junction Box
3.1 Calibration and Range Factors
4.1 Cleaning 4.2 Zero Span Checking
Section 4 Maintenance
4.3 Effect of Moisture Ingression
4.4 Effect of a Grounded Electrode
4.8 Erratic Signal
4.6 Transmitter Fault 4.7 All Checks Good, But No Signal
4.9 Signal Or Indication “Swing”
ChannelMag Section 4 Maintenance
ChannelMag
Section 5 Recommended Spares
5.1 Recommended Spares
