Manuals / Brands / Computer Equipment / Network Card / Asante Technologies / Computer Equipment / Network Card

Asante Technologies ASANTE MacCon Family Ethernet Network Cards for the Macintosh , Installing a MacCon LC Card

1 65

Download 65 pages, 711.2 Kb

Installing Asanté MacCon Cards 2-9

Installing a MacCon LC Card

If you have a Macintosh LC, LCII, or Color Classic computer, use the

MacCon LCIII or MacCon-i LC card to connect the Macintosh to the

Ethernet.

Caution

Only the LC and LCII computers can accept FPUs on the LC card. If

your Macintosh already has a math co-processor (or FPU), do not

install the Asanté math co-processor option with the card.

Refer to your Macintosh User’s Guide for illustrated instructions for

opening your computer.

∆

Note: LCIII card

—You can disable link integrity on the Mac-

Con LCIII card by setting the JP2 jumper as indicated in Figure

2-8. (For example, hubs made before the 10BaseT speciﬁca-

tions were published do not support link integrity.)

Figure 2-8

Disabling link integrity, LCIII card

To install the MacCon LC card into the expansion slot on the moth-

erboard, perform the following steps:

1

Power down the Macintosh. Disconnect and remove the

power cable.

2

Open the Macintosh.

3

Make sure you are grounded: check that your anti-static

wrist strap is properly attached to your wrist and to the

Macintosh chassis.

4

Insert the card into the expansion slot.

!

JP2 disabled

enabled

JP2–link integrity

Contents

Main Page Page Page Asking for assistance Technical support hours Tell us what you think Table of Contents Page List of Figures Chapter 1 and Introducing the Asant MacCon Cards Summary of MacCon Card Features The Math Co-processor Option Asant EtherTalk Installer Software Installing Asant MacCon Cards Checking the Requirements Preparing for the Installation Observing the Safety Rules The MacCon NuBus Card Installing the MacCon NuBus Card Page Installing the MacCon 610 Card Page Page Installing a MacCon LC Card Page Page Page Installing the MacCon3 IIsi and MacCon 30i Cards Setting the Cable Type on the Daughter Card Video Options Setting the Slot Address for Two Cards Installing the Math Co-processor Installing in a Macintosh IIsi 1 2 3 4 5 6 Page Page Page 3 4 5 6 7 Installing a MacCon+ SE Card in a Macintosh SE Setting the Cable Type on the Daughter Card 1 2 3 4 5 6 7 8 9 10 11 12 Connecting the Macintosh to the Network 1 2 1 2 3 Installing the EtherTalk Software 1 2 3 4 5 Accessing Network Services 1 2 3 4 5 Chapter 3 IP Addressing Asant SNMP MacAgent Introduction Requirements Asant SNMP MacAgent and the TCP/IP Protocol Accessing Asant MacAgent MIB AsantView In-Band Network Management Software Installing SNMP MacAgent Page Conguring SNMP MacAgent Asant SNMP Conguration Parameters AsantView Network Management Station Other Network Management Software Chapter 4 Changing from EtherTalk to LocalTalk Using TroubleShooter and ADLS Diagnostic Software Running TroubleShooter Diagnostics Starting TroubleShooter Diagnostics Page Page Page If a test fails Page Page Chapter 5 Troubleshooting Running TroubleShooter Macintosh IIsi with a PDS Slot Installing the Math Co-processor Option Other Tips Page Page Appendix A The specications for the Asant MacCon cards are given below. MacCon Specications 23 2 Technical Specications Ethernet Address MacCon LEDs The table below lists the Ethernet specications. Ethernet Specications Connector Pin-outs AAUI Connector The following table describes the AUI connector pinouts. RJ-45 Connector