Manuals / Brands / Computer Equipment / Network Card / Asante Technologies / Computer Equipment / Network Card

Asante Technologies ASANTE MacCon Family Ethernet Network Cards for the Macintosh Video Options , Setting the Slot Address for Two Cards

1 65

Download 65 pages, 711.2 Kb

2-14 Installing Asanté MacCon Cards

Video Options

Even though the Macintosh IIsi has only one expansion slot, you can

install both a MacCon3 IIsi card and the Radius video card. An exter-

nal interface device is not needed and high performance is main-

tained. The following table shows which MacCon cards you can

install with the Radius and SuperMac video cards and which ports are

available for connecting to the Ethernet.

Setting the Slot Address for Two Cards

Since the two cards cannot use the same slot address, change the slot

address for the Asanté card by setting the JP1 and JP2 jumpers on the

larger controller card. If you keep the default slot address of 9 for the

video card, you can set the Asanté card address to A, B, or E, as

shown in the following table.

MacCon compatibility with third-party video cards

Video card Asanté card Ethernet ports available

Radius Pivot IIsi MacCon3 IIsi RJ-45 and BNC

SuperMac

Spectrum/8●24 PDQ

Spectrum/8●24 PDQ si

FriendlyNet IIsi AAUI with FriendlyNet

Media Adapter for

10BaseT/Thin/thick

JP1 and JP2

jumpers

Address Set Address Set

9A

EB

Contents

Main Page Page Page Asking for assistance Technical support hours Tell us what you think Table of Contents Page List of Figures Chapter 1 and Introducing the Asant MacCon Cards Summary of MacCon Card Features The Math Co-processor Option Asant EtherTalk Installer Software Installing Asant MacCon Cards Checking the Requirements Preparing for the Installation Observing the Safety Rules The MacCon NuBus Card Installing the MacCon NuBus Card Page Installing the MacCon 610 Card Page Page Installing a MacCon LC Card Page Page Page Installing the MacCon3 IIsi and MacCon 30i Cards Setting the Cable Type on the Daughter Card Video Options Setting the Slot Address for Two Cards Installing the Math Co-processor Installing in a Macintosh IIsi 1 2 3 4 5 6 Page Page Page 3 4 5 6 7 Installing a MacCon+ SE Card in a Macintosh SE Setting the Cable Type on the Daughter Card 1 2 3 4 5 6 7 8 9 10 11 12 Connecting the Macintosh to the Network 1 2 1 2 3 Installing the EtherTalk Software 1 2 3 4 5 Accessing Network Services 1 2 3 4 5 Chapter 3 IP Addressing Asant SNMP MacAgent Introduction Requirements Asant SNMP MacAgent and the TCP/IP Protocol Accessing Asant MacAgent MIB AsantView In-Band Network Management Software Installing SNMP MacAgent Page Conguring SNMP MacAgent Asant SNMP Conguration Parameters AsantView Network Management Station Other Network Management Software Chapter 4 Changing from EtherTalk to LocalTalk Using TroubleShooter and ADLS Diagnostic Software Running TroubleShooter Diagnostics Starting TroubleShooter Diagnostics Page Page Page If a test fails Page Page Chapter 5 Troubleshooting Running TroubleShooter Macintosh IIsi with a PDS Slot Installing the Math Co-processor Option Other Tips Page Page Appendix A The specications for the Asant MacCon cards are given below. MacCon Specications 23 2 Technical Specications Ethernet Address MacCon LEDs The table below lists the Ethernet specications. Ethernet Specications Connector Pin-outs AAUI Connector The following table describes the AUI connector pinouts. RJ-45 Connector