Manuals / Brands / Computer Equipment / Network Card / Asante Technologies / Computer Equipment / Network Card

Asante Technologies ASANTE MacCon Family Ethernet Network Cards for the Macintosh Installing the MacCon3 IIsi and MacCon 30i Cards

1 65

Download 65 pages, 711.2 Kb

Installing Asanté MacCon Cards 2-13

Installing the MacCon3 IIsi and MacCon 30i Cards

If you have a Macintosh IIsi or a Macintosh SE/30, use a MacCon3 IIsi

or a MacCon+ 30i to connect to the Ethernet. (The cards are not

designed for a Macintosh SE.)

Each card consists of two parts:

❏The larger controller card, which plugs into the expansion

slot in the Macintosh.

❏The smaller daughter card, which is mounted on the rear

access port to enable a connection to the Ethernet cable.

You connect the two cards with a ribbon cable after installing them.

Setting the Cable Type on the Daughter Card

With the MacCon+ 30iET and MacCon+ 30iE, set the cable type by

pressing the switch in the lower left corner on the daughter card.

Select the switch position, as speciﬁed in the table below, by press-

ing the switch with a pointed tool. With the MacCon+ 30iET, select

TPL if your hub supports link integrity; select TPN if it does not.

The MacCon3 card has autosensing ports and does not require a

switch to be set.

MacCon+ 30iET MacCon+ 30iE

TPL 10BaseT

Link integrity enabled

TPN 10BaseT

Link integrity not enabled

TK Thick

TN Thin

TK Thick

TPL

TPN

TK

TN

TK

Switch Switch

Contents

Main Page Page Page Asking for assistance Technical support hours Tell us what you think Table of Contents Page List of Figures Chapter 1 and Introducing the Asant MacCon Cards Summary of MacCon Card Features The Math Co-processor Option Asant EtherTalk Installer Software Installing Asant MacCon Cards Checking the Requirements Preparing for the Installation Observing the Safety Rules The MacCon NuBus Card Installing the MacCon NuBus Card Page Installing the MacCon 610 Card Page Page Installing a MacCon LC Card Page Page Page Installing the MacCon3 IIsi and MacCon 30i Cards Setting the Cable Type on the Daughter Card Video Options Setting the Slot Address for Two Cards Installing the Math Co-processor Installing in a Macintosh IIsi 1 2 3 4 5 6 Page Page Page 3 4 5 6 7 Installing a MacCon+ SE Card in a Macintosh SE Setting the Cable Type on the Daughter Card 1 2 3 4 5 6 7 8 9 10 11 12 Connecting the Macintosh to the Network 1 2 1 2 3 Installing the EtherTalk Software 1 2 3 4 5 Accessing Network Services 1 2 3 4 5 Chapter 3 IP Addressing Asant SNMP MacAgent Introduction Requirements Asant SNMP MacAgent and the TCP/IP Protocol Accessing Asant MacAgent MIB AsantView In-Band Network Management Software Installing SNMP MacAgent Page Conguring SNMP MacAgent Asant SNMP Conguration Parameters AsantView Network Management Station Other Network Management Software Chapter 4 Changing from EtherTalk to LocalTalk Using TroubleShooter and ADLS Diagnostic Software Running TroubleShooter Diagnostics Starting TroubleShooter Diagnostics Page Page Page If a test fails Page Page Chapter 5 Troubleshooting Running TroubleShooter Macintosh IIsi with a PDS Slot Installing the Math Co-processor Option Other Tips Page Page Appendix A The specications for the Asant MacCon cards are given below. MacCon Specications 23 2 Technical Specications Ethernet Address MacCon LEDs The table below lists the Ethernet specications. Ethernet Specications Connector Pin-outs AAUI Connector The following table describes the AUI connector pinouts. RJ-45 Connector