Asus TUSL2 3.7.4Accelerated Graphics Port (AGP) Pro Slot, AGP Pro

3.HARDWARE SETUP

3.7.4Accelerated Graphics Port (AGP) Pro Slot

This motherboard provides an accelerated graphics port (AGP) pro slot to support a new generation of AGP graphics cards with ultra-high memory bandwidth.

COM1

AGP Card without Retention Notch

TOP VIEW

TUSL2

20-pin bay

28-pin bay

Rib (inside slot)

Rib

TUSL2 Accelerated Graphics Port (AGP PRO)

CAUTION! The AGP Pro slot is shipped with a warning label over the 20-pin bay. DO NOT remove this label and the safety tab underneath it if you will be using an AGP card without a retention notch. Removing may cause the

card to shift and may cause damage to your card, slot, and motherboard. Remove ONLY when you will be using an AGP Pro card. Use a rigid tip, such as a pen tip, to dislodge and remove the tab from the bay.

Removing the tab

Expansion Cards

3. H/W SETUP

ASUS TUSL2 User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS TUSL2 Manual Revision: 1.03 E811 ASUSTeK COMPUTER INC. (Asia-Pacific) ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) CONTENTS 3.7.1 Installing an Expansion Card 3.7.2 Assigning IRQs for Expansion Cards 3.7.3 Communication and Networking Riser (CNR) Slot 3.7.4 Accelerated Graphics Port (AGP) Pro Slot INDEX FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver 1.1How This Manual Is Organized 1.2 Item Checklist 2.1The ASUS TUSL2 2.1.1 Specifications 2. FEATURES Around-the-Clock CNR Support: Enhanced ACPI & Anti-Boot 2.1.2Specifications–OptionalComponents 2.1.3 Performance 2.1.4Intelligence 2.2TUSL2 Motherboard Components Page 3.1TUSL2 Motherboard Layout 3.2Layout Contents SETUP H/W 3. HARDWARE SETUP 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Feature Settings 1) JumperFree™ Mode (JEN) 4.4 Advanced Menu NOTE: In JumperFree™ mode, all dip switches must be set to OFF Setting 2)ATA100 / RAID 0/1 (JP3) JP3 3)Onboard IDE ( JP4) JP4 4)USB Device Wake Up (USBPWR01, USBPWR23) Control NOTES 1.For suspend to RAM function, these jumpers must be set to Enable 5)USB/CNR Selection (OC3) OC3 Enable CNR Enable USB23 6)Keyboard Power Up (KBPWR) 7)CPU External Frequency Setting (DSW) CPU Speed Advanced Menu CPU Core:Bus Freq. Multiple External Frequency Table CPU:DRAM CPU Frequency Selection Switches Ratio 8)Voltage I/O Setting (VIO) Setting VIO 9)Bass Center Setting (CENTER/BASS, BASS/CENTER) 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards 3.7.3Communication and Networking Riser (CNR) Slot 3.7.4Accelerated Graphics Port (AGP) Pro Slot 3.8External Connectors 3)Universal Serial BUS Ports 0 & 1 (Black two 4-pinUSB) USB Headers 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) Serial Port Connectors (Teal/Turquoise 9-pin COM1 pin COM2) Onboard Serial Port 1/2 9)Floppy Disk Drive Connector (34-1pinFLOPPY) (40-1pin PRIMARY ATAIDE and SECONDARY ATAIDE) See 5.4 Software Setup TIP: two separate See 4.6 Boot Menu 11)IDE Activity LED (2-pinIDELED) do not place jumper caps over these pins 13)Internal Audio Connectors (4-pinCD1, AUX, MODEM) 14)Headphone True-LevelLine Out Header (3-pinHPHONE) 15)Internal Microphone Connector (3-pinMIC2) 16)ASUS iPanel Connector (12-1pin AFPANEL) infrared module 17)ASUS iPanel Audio Connector (12-1pin AAPANEL) 18)Chassis Intrusion Lead (2-pinACHA) 19)Wake-On-LANConnector (3-pinWOL_CON) Wake On LAN or PCI Modem 4.5.1 Power Up Control 20)Wake-On-RingConnector (2-pinWOR_CON) IMPORTANT: 21)LCD-TVHeaders (18-pin, 18-1pin LCD TV) These headers require optional modules for LCD or TV output 22)USB Header (10-1pin USB23) 23)ASUS SmartCard Connector (10-1pin SMARTCON) 24)ATX Power Supply Connector (20-pinblock ATXPWR) 25)Power Supply Thermal Sensor Connector (2-pinJTPWR) 26)System Power LED Lead (3-1pin PWRLED) 27)Keyboard Lock Switch Lead (2-pinKEYLOCK) 28)System Warning Speaker Connector (4-pinSPEAKER) 29)System Message LED Lead (2-pinMSG.LED) 30)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2 Updating BIOS Procedures Page 8.Follow the onscreen instructions to continue 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] A Note about Passwords Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu CPU Vcore CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Disabled] BIOS Update [Enabled] PS/2 Mouse Function Control [Auto] Notes for JumperFree Mode 4.4.1Chip Configuration SDRAM RAS to CAS Delay SDRAM RAS Precharge Time SDRAM Cycle Time (Tras, Trc) [6T, 8T] SDRAM Page Closing Policy [One Bank] CPU Latency Timer [Enabled] Memory Hole At 15M-16M[Disabled] PCI 2.1 Support [Enabled] High Priority PCI Mode [Disabled] Onboard PCI IDE Enable [Both] SDRAM Data Driving Mode [Normal] 4.4.2I/O Device Configuration UART2 Use [COM Port] Onboard Parallel Port [378H/IRQ7] Parallel Port Mode ECP DMA Select Parallel Port Mode [ECP+EPP] 4.4.3PCI Configuration PCI/PNP IRQ Resource Exclusion 4.4.4Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] Suspend Mode [Disabled] 4.5.1Power Up Control Wake On PS2 KB/PS2 Mouse/CIR [Disabled] Wake Up By PS2 Keyboard [Space Bar] Wake On PS2 KB/PS2 Mouse/CIR Wake On USB for S3 or S4 State [Disabled] USB Device Wake Up 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence SCSI/Promise Boot Sequence [Promise/SCSI] Plug & Play O/S [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Page 5.1Install Operating System 5.2 Start Windows 5.3TUSL2 Motherboard Support CD 5.3.1 Installation Menu Windbond Smart Manager Application: PC-Cillin 2000Vx.xx: Adobe Acrobat Reader Vx.x: Cyberlink Video and Audio Applications: 5.4Using the Promise Chip for RAID 0 or 5.4.1Installing the Hard Disks 5.4.2 Enter FastTrak100 BIOS and FastBuild Utility 5.4.3Creating a RAID 0 Array 5.4.4Creating a RAID 1 Array Please Select A Source Disk <Ctrl-Y <Y <N <N 5.4.5Other FastBuild Utility Commands 5.4.6 Alternative Set Ups and Other Details 5.5.1 Win9x-MEPromise® FastTrak100 Speed BIOS 5.5.2Win2000 Promise® FastTrak100™ Lite/Simple Controller Driver (This page was intentionally left blank. ) 6.1Winbond Smart Manager 6.1.1 Setting Up Smart Manager REFERENCES/W6 6. SOFTWARE REFERENCE Restart Do not install unless only 6.1.2Starting to Use Smart Manager 6.1.3Smart Manager Modes 6.2ASUS PC Probe 6.2.1 Starting ASUS PC Probe 6.2.2Using ASUS PC Probe Monitoring Information Utility 6.2.3ASUS PC Probe Task Bar Icon 6.3Multi-ChannelAudio Feature Setup 6.3.1 The C-MediaAudio Mixer 6.3.2 The C-MediaAudio Demo Program 6.3.3 Connector Configuration 6.4ASUS LiveUpdate 6.5CyberLink PowerPlayer SE 6.5.1 Starting CyberLink PowerPlayer SE 6.5.2 CyberLink PowerPlayer Control Panel 6.6CyberLink VideoLive Mail 6.6.1Starting VideoLive Mail 6.6.2 CyberLink VideoLive Mail User Interface Page 7.1 Glossary APPENDIX Boot Bus Master IDE Byte (Binary Term) COM Port LPT Port (Line Printer Port) MMX (Klamath) CPU as well as other OnNow PC100 ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions) INDEX Page Page NOTES