5.2Time Menu
The time display flashes on the screen when the time has not yet been set or after a 4-hour power outage. Use the Time menu to select the time format (12-hour or 24-hour) and to set the clock and date.
NOTE: The date is used to determine the sunset and sunrise times.
5.3Configuration Menu (Conf)
Use the Configuration menu to set the following parameters (see sections 5.3.1 to 5.3.4).
5.3.1 Backlight mode (SCRN)
The screen is lit at high intensity for 8 seconds when you press any button. The rest of the time, depending on the backlight mode selected, the screen behaves as follows:
Scrn Off: The screen is not lit.
Scrn On HI: The screen is lit at high intensity.
Scrn On LO: The screen is lit at low intensity (default mode).
5.3.2Automatic Daylight Savings Time Changeover (DLS)
When automatic daylight savings time changeover is on (DLS On), the TI073 changes to daylight savings time (summer time) at 2:00 am on the second Sunday of March and changes back to normal time (winter time) at 2:00 am on the first Sunday of November. This function is enabled (DLS On) by default.
5.3.3Latitude and Longitude Coordinates (LAT and LONG)
The coordinates are used to turn the lights on at sunset and off at sun- rise. The latitude is set to +45 and longitude to -75 by default. These settings provide approximate sunset and sunrise times for most North American cities. To obtain your city’s coordinates (or those of a nearby city), see the coordinates table. You can also obtain this information at www.aubetech.com/timer or with a Global Positioning System (GPS) device. The accuracy of the sunset and sunrise times depends on the accuracy of the coordinates you enter for your city.
NOTE: Enter a negative value for a south latitude or a west longitude.
5.3.4 Correction Factor (ADJ)
If your city’s time zone is based on political or economic boundaries instead of its coordinates, your lights might switch on or off too early or too late with respect to sunrise and sunset. In this case, apply a correction factor (+1 or -1 hour; refer to addendum). Otherwise, leave it at 0 (default value).
5.4Program Menu (Prog)
Use the Program menu to set the programs; i.e. the times you want the lights to turn On or Off when the switch is in Automatic mode. To set a program, proceed as follows:
nSelect a program number (see section 5.4.1)
oSet the day(s) of the program (see section 5.4.2)
pSet the program start time (see section 5.4.3)
5.4.1 Selecting a program number
| You can set up to 21 “On” programs | | |
| (“P01 On” to “P21 On”) and 21 “Off” | | |
| programs (“P01 Off” to “P21 Off”). | | |
| Select an “On” program to set when to | | |
| turn the lights on. Select an “Off” | | |
| program to set when to turn the lights | “P01 On” | “P01 Off” |
| off. |
| | |
5.4.2 Setting the day(s) of the program
After selecting a program, set the day(s) of the program. You can select a specific day, all 7 days or “none”. Choose “none” for any unused program.
5.4.3 Setting the program start time
After setting the day(s) of the program, set its start time. You can select either a specific time, the sunset time or the sunrise time:
•To select a specific time:
(1)Advance to the hour setting and select the hour.
(2)Advance to the minutes setting and select the minutes.
•To select sunset or sunrise time:
(1)Advance to the hour setting and select the sunset time or
sunrise time. (When you scroll, the sunset time 
and sunrise time 
appear between 11 pm and 12 am.)
(2)To enter an offset (from -70 to +70 minutes in 10-minute increments) between the sunset or sunrise time and the program start time, advance to the minutes setting and change the minutes.
• EXAMPLE: If the sunset time is 6:13 pm and you change the minutes to display 6:43 pm, you have entered a delay of 30 minutes. If, later in the year, the sunset time is 4:01 pm, the program will start at 4:31 pm.
• NOTE: When you enter an offset, 
appears along with 
or 
when you display the sunset or sunrise time. To remove the offset, display the sunset or sunrise time and change the minutes until 
disappears.
5.4.4 Examples
Example 1: The lights turn on at sunset and off at 11:00 pm every day (default setting).
Program | Days | Time | Program | Days | Time |
P01 On | All 7 | sunset | P01 Off | All 7 | 11:00 |
| days | | | days | pm |
P02 On to | None | — | P02 Off to | None | — |
P07 On | | | P07 Off | | |
Example 2: The lights turn on at sunset and off at sunrise every day.
Program | Days | Time | Program | Days | Time |
P01 On | All 7 | sunset | P01 Off | All 7 | sunrise |
| days | | | days | |
P02 On to | None | — | P02 Off to | None | — |
P07 On | | | P07 Off | | |
Example 3: The lights turn on at 8:00 pm every day and turn off at 10:00 pm every day except on Saturday night when they turn off at 1:00 am.
Program | Days | Time | Program | Days | Time |
P01 On | All 7 days | 8:00 pm | P01 Off | Sunday (Su) | 10:00 pm |
P02 On | None | — | P02 Off | Monday (Mo) | 10:00 pm |
P03 On | None | — | P03 Off | Tuesday (Tu) | 10:00 pm |
P04 On | None | — | P04 Off | Wednesday (We) | 10:00 pm |
P05 On | None | — | P05 Off | Thursday (Th) | 10:00 pm |
P06 On | None | — | P06 Off | Friday (Fr) | 10:00 pm |
P07 On | None | — | P07 Off | Sunday (Su) | 1:00 am |
Be careful about overlapping!
For example, if you set “P01 Off” at 10:00 pm for all 7 days and set “P02 Off” to 11:00 pm for Saturday, on Saturday, the lights will turn off at 10:00 pm, not 11:00 pm, since “P01 Off” is set to an earlier time than “P02 Off”.
sReset to Default Settings
To return the switch to its default settings, simultaneously press both main and left buttons and hold. The software version will appear for 5 seconds. RST will appear for the next 5 seconds. Release the buttons when all segments appear on the screen. The switch is now reset (see default settings in the menu flowchart).
tKeypad Lock 
When the keypad is locked, the 
icon appears on the screen and the only change permitted is the changing of the state. For example, if the lights are off, they will turn on when you press the main button. However, in Automatic mode, the default state for the current program will be overridden until the next program starts. If you press the main button again before the start of the next program, the lights return to their initial state. To lock or unlock the keypad, press the buttons in the following order:
2 sec.
NOTE: You must perform the whole procedure in an interval of 2 seconds. If the procedure was not properly performed, wait another 2 seconds before retrying.
uTroubleshooting
The screen is blank. | • A light bulb is burned out. |
| • The safety switch is pulled out (see section |
| 4). |
The display is faded or | • The load is less than 40 W. |
irregular. | • The ambient temperature is either below or |
| above the switch’s operating temperature. |
| |
The metal plate is hot. | This is normal with high loads (maximum of |
| 500 W). |
| |
The sunset or sunrise | • The date or time is wrong |
time is inaccurate. | (see section 5.2). |
| • The longitude or latitude is wrong |
| (see section 5.3.3). |
| • The correction factor is wrong |
| (see section 5.3.4). |
| • You have entered an offset |
| (see section 5.4.3). |
vSpecifications
Supply: 120 VAC, 60 Hz
Minimum load: 40 watts
Maximum load: 500 watts
Operating temperature range: -15 °C to 50 °C (5 °F to 122 °F)
Storage temperature range: -40 °C to 60 °C (-40 °F to 140 °F)
Power outage: The screen is blank. Only the time must be set if the outage lasts more than 4 hours; all other settings and programs are permanently saved.
Latitude range: from -65° to +65°
Solar table precision: +/- 11 min. (within ±60° latitude)
Certification: UL (c UL us)
;Warranty
AUBE warrants this product, excluding battery, to be free from defects in the work- manship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the war- ranty period the product is determined to be defective or malfunctions, AUBE shall repair or replace it (at AUBE's option).
If the product is defective,
(i)return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or
(ii)contact AUBE. AUBE will make the determination whether the product
should be returned, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by AUBE that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
AUBE's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAM-
AGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the exclusion or limita- tion of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUD- ING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR- TICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some provinces, states or regions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary according to the province, state or region.
Technical Assistance
705 Montrichard Avenue Saint-Jean-sur-Richelieu, Quebec J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
Email: aube.service@honeywell.com
For more information on our products, go to
www.aubetech.com
