·Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot.
·When the LP gas cylinder is connected, the grill must be kept outside in a
·Move gas hose as far away as possible from hot surfaces.
How to Connect your LP gas cylinder (See STEP 22 of Assembly Instructions for diagram)
1)Make sure all of the control knobs are turned to the “off” position and verify that the LP gas cylinder valve is closed by turning the handle on the LP gas cylinder valve clockwise until it stops.
2)Remove the protective cap from the LP cylinder gas nozzle.
3)Hold regulator in a straight line with LP cylinder gas nozzle so the connection does not cross thread.
4)Insert Regulator nipple into the LP cylinder nozzle opening.
5)Hand tighten coupling nut in a clockwise direction. Do not use tools.
6)Perform a Leak Test. (See STEP 10 of Assembly Instructions for Leak Test Instructions)
How to Disconnect your LP gas cylinder
1)Turn all control knobs to the “off” position and turn the handle on the LP gas cylinder clockwise until it stops.
2)Turn coupling nut on regulator in a
3)Place the protective cap over LP cylinder gas nozzle.
BEFORE USING YOUR
LP GAS GRILL
Selecting a Location
·Do not use an LP gas grill indoors, on recreational vehicles, or on a boat.
·This LP gas grill is for outdoor use only and should be placed on firm, level surface. The grill should be setup in an open area with good ventilation, away from high traffic areas and combustible materials.
·Combustible or flammable materials should never be used or stored within 36 inches of the back or sides of your LP gas grill.
·Locate your LP gas grill at least 10 feet away from your house or any building. Do not use the grill in a garage, breezeway, carport, porch, or under a surface that can catch fire.
Precautions
·Carefully read the Important Safeguards section of this manual (pages 2 through 4). Make sure you follow and understand all instructions and warnings. If you have any questions regarding these pages, call
·This installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1, or
·If an external electrical source is utilized, the outdoor cooking appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Codes, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
·If any electric appliance or rotisserie is used with the LP gas grill, do not allow cords to touch or be near hot surfaces. Electric cords should be placed away from walkways to avoid a tripping hazard.
·Grill storage cover must be removed and placed at least 36 inches from the LP gas grill while in use. The grill cover is made of a flammable material. The grill must be completely cooled before putting the cover back on the grill.
·Never store a spare or disconnected LP gas cylinder under or near this LP gas grill.
·Inspect the hose and regulator assembly before each use. If the hose is cut or damaged or shows signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose must be replaced with an assembly specified by the manufacturer prior to the further use of the LP gas grill.
·Use only the hose and regulator assembly that is supplied with your LP gas grill.
·Use of this LP gas grill other than for the intended use, or alteration of the LP gas grill in any way may not be safe and will void any warranty.
·LP gas is not natural gas. The conversion or attempted use of natural gas in an LP unit is dangerous and will void your warranty.
·Never use an LP gas cylinder if it shows signs of: dents, gouges, bulges, fire damage, corrosion, leakage, excessive rust, or other forms of visual external damage; it may be hazardous and should be checked by a Liquefied Petroleum supplier. Do not use an LP cylinder with a damaged valve.
·Never use charcoal in your LP gas grill. Do not use aerosols or store flammable liquids or materials near this gas grill.
29
