Manuals / Avaya / Computer Equipment / Switch

Avaya P333R-LB manual Powering Up the Avaya P330, Powering On Avaya P330 Module AC

Models: P333R-LB

1 218
Download 218 pages 57.22 Kb
Page 43
Image 43

Chapter 5

Powering Up the Avaya P330

This section describes the procedures for powering up the Avaya P330 unit.

Powering On – Avaya P330 Module AC

For the AC input version of the Avaya P330, insert the AC power cord into the power inlet in the back of the unit. The unit powers up.

If you are using a BUPS, insert a power cord from the BUPS into the BUPS connector in the back of the unit. The unit powers up even if no direct AC power is applied to the unit.

After power up or reset, the Avaya P330 performs a self test procedure. applied to it.

Powering On – Avaya P330 Module DC

For the DC input version of the Avaya P330, connect the power cable to the switch at the input terminal block.

1The terminals are marked “+”, “-“ and with the IEC 5019a Ground symbol.

2The size of the three screws in the terminal block is M3.5.

3The pitch between each screw is 9.5mm.

Connect the power cable to the DC power supply. After power up or reset, the Avaya P330 performs a self test procedure.

Warning: Before performing any of the following procedures, ensure that DC power is OFF.

Caution: This product is intended for installation in restricted access areas and is approved for use with 18 AWG copper conductors only. The installation must comply with all applicable codes.

Warning: The proper wiring sequence is ground to ground, positive to positive and negative to negative. Always connect the ground wire first and disconnect it last.

Avaya P333R-LB User’s Guide

29

Page 42 Page 44
Page 43
Image 43
Avaya P333R-LB manual Powering Up the Avaya P330, Powering On Avaya P330 Module AC, Powering On Avaya P330 Module DC
Page 42 Page 44

P333R-LB specifications

The Avaya P333R-LB is a robust and versatile switch that is part of Avaya's portfolio aimed at enterprise networking solutions. This switch is designed to enhance the performance and scalability of network infrastructure while ensuring high availability and reliability.

One of the main features of the P333R-LB is its Layer 3 switching capability, which allows for efficient routing within an organization's network. This capability is particularly beneficial for organizations with multiple VLANs, as it simplifies the routing process and ensures that data packets are transmitted in the most efficient manner possible.

The P333R-LB is equipped with advanced Quality of Service (QoS) features to prioritize traffic based on the type of application being used. This ensures that critical applications, such as VoIP and video conferencing, receive the necessary bandwidth and low latency required for optimal performance. Additionally, it supports both IPv4 and IPv6 protocols, making it adaptable to a variety of networking environments.

Another important feature of the Avaya P333R-LB is its stackable design. This allows multiple switches to be interconnected, creating a single logical unit. This stacking capability not only simplifies management but also increases overall network capacity and redundancy. In case of a hardware failure, the stack can continue operating without interruption, maintaining network integrity and service continuity.

The switch also integrates advanced security features, including support for MAC filtering, access control lists, and port security. These features help to safeguard network resources from unauthorized access and potential threats. Moreover, the P333R-LB supports 802.1X port-based authentication, which adds an additional layer of security during user access to the network.

The Avaya P333R-LB comes with multiple Gigabit Ethernet ports, allowing for high-speed connectivity to devices such as servers, workstations, and IP phones. This ensures that all devices on the network can communicate effectively, supporting the demands of modern enterprise environments.

For management and monitoring, the P333R-LB offers a user-friendly web interface along with SNMP support, enabling network administrators to easily configure settings and monitor network performance. This simplicity in management is crucial for IT teams that need to ensure optimal network performance while minimizing downtime.

In summary, the Avaya P333R-LB is a feature-rich, scalable, and reliable switch that meets the needs of demanding enterprise networks. With its advanced technologies, QoS support, stackable design, robust security features, and high-speed connectivity options, the P333R-LB is positioned to support a wide range of applications and enhance overall network performance.