Bakers Pride Oven GDCO-G, BCO-G manual For a single unit Refer to Figure

For a single unit: Refer to Figure 4

(1)Tilt Oven over to left-hand side and attach two 31” legs on the right-hand side with three ½” bolts and washers. Tighten firmly.

(2)Using proper lifting equipment, lift up the left-hand side and attach two 31” legs on the left-hand side the same way.

For a stack of two ovens: Refer to Figure 3

(1)Remove flue from bottom oven prior to stacking. When top oven is properly positioned on bottom oven, re-install the flue back on the bottom oven.

(2)Tilt lower unit over to the left-hand side and position two 6” legs on the right side (one for front and one for back), secure in place by using 4 bolts (3/8”-16) per leg. Tighten firmly.

(3)Using proper lifting equipment, lift up the left side of the unit and attach the other two legs in the same way.

(4)Using the lifting equipment, raise the top oven to proper height and slide on top of the bottom oven. Line up sides and front and fasten to each other at the rear of the units by using a mounting bracket supplied in the stacking kit.

To assemble an open rack stand: Refer to Figure 1

(1)Loosen 12 bolts (attaching 31” legs) slightly.

(2)Remove 4 inner bolts, 1 from each of the 4 legs, place top right angle and top left angle underneath and tighten these 4 bolts.

(3)Insert “Open Rack Shelf” and tighten into place with eight 3/8-16 screws, washers and nuts.

(4)Position “Rack Supports” and tighten in place using 4 each of flat washers and 5/16-18 Hex Nuts.

Fit the Standard Flue Diverter supplied into the hole in the top of the oven for under ventilation hood installation and secure with screws. For direct venting, Flue Adapter and Draft Hood must be placed into the hole on top of the oven.

C. INSTALLATION WITH CASTERS (OPTIONAL): Refer to Figure 4

Four casters (two with wheel brakes) and the mounting hardware are packed and included in the shipment if ordered. Install casters with wheel brakes on the front of the unit. Installation of the unit should be made with a connector that complies with the latest edition of the Standard for Connectors for Movable Gas Appliances ANSI Z21.69 in the USA (CAN CSA-6.16 in Canada) and a quick-disconnect device that complies with the latest edition of the standard for quick disconnect devices for use with gas fuel ANSI Z21.41 in the USA (CSA 6.9 in Canada). Adequate means must be provided to limit the movement of the appliance without depending on the connector and any quick disconnect device or its associated piping to limit appliance movement.

The restraint should be attached to the rear legs of the oven on which casters are mounted. If disconnect of the restraint is necessary, the restraint should be immediately reconnected after the appliance has been returned to its originally installed position.

Figure 1 OPEN RACK STAND ASSEMBLY INSTRUCTIONS: BCO-G & GDCO-G

Open Style Support Leg Not Supplied With Kit

1

2

3

4

5

6

Assembly Instruction

1.Place undershelf (6) between legs & secure with 1/4-20 UNC screws (4), flat washers (3) & locknuts (2). The holes for mounting the wire racks should be toward the front of the oven.

2.Place open rack supports (1) between legs & secure with 1/4-20 UNC screws (4), flat washers (3) & locknuts (2).

3.Slide wire rack supports (5) into position using the holes in the undershelf (6) as a guide.

Item	P/N	Description	Quan
1	21818222	Support, Open Rack	2
2	770504	Lock Nut 1/4-20	12
3	8519600	Washer, Flat 1/4”	12
4	8208200	Screw, 1/4-20 x 3/4”	12
5	21816807	Support, Wire Rack	2
6	21818231	Undershelf, Gas Oven	1

3