Manuals / Brands / Personal Care / Wheelchair / Barco / Personal Care / Wheelchair

Barco R9000893, R9000896 How to use your RCU, Projector Address

1 55

Download 55 pages, 2.1 Mb

Controlling

4-2 5975847 BARCOGRAPHICS 1208s 220197

The BARCOGRAPHICS 1208s can be controlled with

a. the RCU

b. the hardwired RCU (cable not included)

c. the built-in RCU (local keypad)

The procedure and results of controlling the projector with either of

these RCU options is essentially the same.

How to use your RCU

a) Point the front of the RCU towards the reflective screen surface

b) Point the front of the RCU towards one of the IR sensors in the

projector.

When using the wireless remote control, make sure you are within the

effective operating distance (30m, 100ft in a straight line). The

remote control unit will not function properly if strong light strikes the

sensor window or if there are obstacles between the remote control

unit and the projector's IR sensor.

IR Receiver Locations on the Projector:

c) RCU used in a hardwired configuration.

Plug one end of the remote cable in the connector on the bottom of

the RCU and the second side in the connector in the rear panel of the

BARCOGRAPHICS 1208s labelled 'REMOTE'.

d) Built-in RCU (local keypad)

To gain access to the built-in RCU, see paragraph 'The local keypad'

Projector Address

a. hardware set up of the projector address.

Every projector requires an individual address between 0 and 255

which is set with hardware DIP switches inside the projector. To

change that address, contact a BARCO authorized technician.

b. How to control the projector.

The projector's address may be set to any value between 0 and 255.

When the address is set, the projector can be controlled now with :

- the RCU for addresses between 1 and 9.

- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for

addresses between 0 and 255.

Note : a projector will respond to a RCU set to an address of '0'

regardless of what address is set in the projector itself. Address "O"

is therefore a universal address.

c. Using your RCU.

Before using your RCU, it is necessary to enter the projector address

into the RCU (only when that address is between 1 and 9). The

projector with the corresponding address will listen to that specific

RCU.

When address 0, 'zero address' is programmed into the RCU, every

projector, without exception will listen to the commands given by this

RCU.

Ceiling

Screen

IR sensor

RCU800

0

9

7

8

6

5

43

2

1

ENTER

0

9

7

8

6

5

43

2

1

ENTER

365

45°

45°

45°

45°

366

RS232 OUTRS232 IN

IR

REMOTE

Contents

Main Page Page Table of Contents Table of Contents Safety Instructions WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) On safety 1 Notice on Safety PART NUMBER : SER. NUMBER : DEALER : Safety Instructions A. Mains lead (Power cord) with CEE 7 plug B. Power cord with ANSI 73.11 plug 3 4 2 75 ohm Termination Switch for Video signals REAR PANEL TERMINOLOGY Communication Port (800 peripherals) Port 3 Location and Functions of Control b. RCU control panel terminology Back light key ADJ. Address key STBY 3 AC Power (mains) Cord Connection Power Check Switching On/Off Start up with full white image. Signal Input Connection to the Projector : 3-3 5975847 BARCOGRAPHICS 1208S 220197 Connecting a Composite Video source to port 1. VCR S-VHS Audio amplifier Audio amplifier Select 'Selected source' and press ENTER. Highlight 'Picture Tuning' and press ENTER. Connecting a RGB Analog source to port 3. Analog Input Selection : Connecting a RGB Analog source to port 4/5. RGB input selection : 3-5 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) Audio amplifier OFFON Audio amplifier Audio amplifier PERIPHERAL EQUIPMENT 4 How to use your RCU Projector Address a. hardware set up of the projector address. b. How to control the projector. c. Using your RCU. How to display a projector address? Input selection How to program an address into the RCU? Analog Picture Controls Controlling chained projectors. Start Up of the Adjustment Mode 5 Adjustment Mode INSTALLATION GUIDED RANDOM ACCESS Start Up of the Adjustment Mode 6 Starting-Up the Random Access Adjustment mode. ENTER EXIT Overview 'Random Access Adjustment' mode Page Selecting Setup Pattern ENTER EXIT Internal Cross Hatch Pattern ENTER EXIT Random access adjustment mode selection menu. Picture Tuning Color Balance Sync Fast/Slow Adjustment ENTER EXIT Clamp Tuning Peaking Port 2 : Video or S-Video Line Doubler (option) EXIT Color Select ENTER EXIT Focusing ENTER EXIT Focusing color select. ENTER EXIT Midpoint focusing Geometry Adjustments ENTER EXIT ENTER Horizontal Phase Adjustment Raster Shift Adjustment forbidden area projected raster crt faceplate border phosphor border Left-Right (east-west) Adjustments ENTER EXIT Seagull correction Left Side Correction ENTER EXIT Top-Bottom (north-south) Adjustments Seagull Correction ENTER will return to Top-Bottom adjustment menu EXIT will return EXIT Horizontal Size Adjustment ENTER EXIT Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Convergence Adjustment Coarse Convergence Adjustment. Fine Convergence Adjustment. Starting up the Service mode. ENTER EXIT 7 Overview flowchart 'Service' mode. Identification GRAPHICS 1208S Copy a block ENTER EXIT Deletion of blocks Deleting block by block ENTER EXIT Deletion of all blocks ENTER Change password Change Language Run time Set to midposition ENTER will set all settings to their midposition. EXIT will cancel the Undo Midposition Convergence Mid ENTER sets the convergence settings to their midposition. EXIT Dynamic Astigmatism (spot shape adjustment) G2 Adjust 'G2 adjustment should be performed by BARCO personnel, or BARCO authorized dealers'. EXIT Gamma corrections ENTER Projector Warm Up CRT Drive Mode Messages, warnings and failure codes 8 Messages, warnings and failure codes Options IR Receiver 800 Hardwired RCU. 9 shield conductor Projector Control software RCVDS 05 Source Selector VS05 Switcher Options MAGIK Interface Adapter and communication cables Ceiling Mount kit CM100 Orbiting Kit A Orbiting (option) Orbiting Mode Toggle Switches Master/Slave Toggle Orbiting ON/OFF toggle (only in Master Orbiting) Orbiting Speed Toggle (only in MASTER Orbiting) ENTER EXIT Orbiting Alignment Adjustment procedure Stand-Alone projector : ENTER Adjustment procedure multiple projector installations : Adjustment Blocks and Source Numbers 90-99 Adjustment Blocks (memory blocks) B NUMBERS 90 - 99 Source numbers 90 - 99 Insert Card INSERT CARD i-1 5975847 BARCOGRAPHICS 1208S 220197 RCU