Barco R9000893, R9000896 Blanking Adjustments

Random Access Adjustment Mode

6-15

5975847 BARCOGRAPHICS 1208S 220197

Blanking Adjustments

Blanking adjustments affect only the edges of the projected image

and are used to frame the projected image on to the screen and to hide

or black out unwanted information (or noise). A 0% on the bar scale

indicates no blanking.

To start up the Blanking adjustments, follow the next procedure :

Push the control stick forward or backward to highlight BLANKING on

the Geometry menu and then press ENTER.Select with or

then <ENTER>

<EXIT> to return.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return.

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Bottom blanking

Top blanking

Right blanking

L

eft blanking

The following blanking corrections are possible :

- top blanking

- bottom blanking

- left blanking

- right blanking

Therefore :

- if the internal # pattern was selected, this pattern remains on the

screen.

- if the genlocked pattern was selected, the external source

will be displayed.

Adjust the next blanking alignments until the image is correctly

framed or the unwanted information is blanked out.

To enter a blanking alignment, push the control stick forward or

backward to highlight a function and press ENTER to activate this

function.

Press EXIT to return.

BLANKING

Select with or

then <ENTER>

<EXIT> to return

TOP

BOTTOM

LEFT

RIGHT

Adjustment of the blanking on the left side

Adjustment of the blanking on the right side

Adjustment of the blanking on the of the image

Correct by pushing the control stick forward

or backward

Adjustment of the blanking on the bottom of the image

Correct by pushing the control stick to the

right or to the left

Contents

Main Page Page Table of Contents Table of Contents Safety Instructions WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) On safety 1 Notice on Safety PART NUMBER : SER. NUMBER : DEALER : Safety Instructions A. Mains lead (Power cord) with CEE 7 plug B. Power cord with ANSI 73.11 plug 3 4 2 75 ohm Termination Switch for Video signals REAR PANEL TERMINOLOGY Communication Port (800 peripherals) Port 3 Location and Functions of Control b. RCU control panel terminology Back light key ADJ. Address key STBY 3 AC Power (mains) Cord Connection Power Check Switching On/Off Start up with full white image. Signal Input Connection to the Projector : 3-3 5975847 BARCOGRAPHICS 1208S 220197 Connecting a Composite Video source to port 1. VCR S-VHS Audio amplifier Audio amplifier Select 'Selected source' and press ENTER. Highlight 'Picture Tuning' and press ENTER. Connecting a RGB Analog source to port 3. Analog Input Selection : Connecting a RGB Analog source to port 4/5. RGB input selection : 3-5 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) Audio amplifier OFFON Audio amplifier Audio amplifier PERIPHERAL EQUIPMENT 4 How to use your RCU Projector Address a. hardware set up of the projector address. b. How to control the projector. c. Using your RCU. How to display a projector address? Input selection How to program an address into the RCU? Analog Picture Controls Controlling chained projectors. Start Up of the Adjustment Mode 5 Adjustment Mode INSTALLATION GUIDED RANDOM ACCESS Start Up of the Adjustment Mode 6 Starting-Up the Random Access Adjustment mode. ENTER EXIT Overview 'Random Access Adjustment' mode Page Selecting Setup Pattern ENTER EXIT Internal Cross Hatch Pattern ENTER EXIT Random access adjustment mode selection menu. Picture Tuning Color Balance Sync Fast/Slow Adjustment ENTER EXIT Clamp Tuning Peaking Port 2 : Video or S-Video Line Doubler (option) EXIT Color Select ENTER EXIT Focusing ENTER EXIT Focusing color select. ENTER EXIT Midpoint focusing Geometry Adjustments ENTER EXIT ENTER Horizontal Phase Adjustment Raster Shift Adjustment forbidden area projected raster crt faceplate border phosphor border Left-Right (east-west) Adjustments ENTER EXIT Seagull correction Left Side Correction ENTER EXIT Top-Bottom (north-south) Adjustments Seagull Correction ENTER will return to Top-Bottom adjustment menu EXIT will return EXIT Horizontal Size Adjustment ENTER EXIT Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Convergence Adjustment Coarse Convergence Adjustment. Fine Convergence Adjustment. Starting up the Service mode. ENTER EXIT 7 Overview flowchart 'Service' mode. Identification GRAPHICS 1208S Copy a block ENTER EXIT Deletion of blocks Deleting block by block ENTER EXIT Deletion of all blocks ENTER Change password Change Language Run time Set to midposition ENTER will set all settings to their midposition. EXIT will cancel the Undo Midposition Convergence Mid ENTER sets the convergence settings to their midposition. EXIT Dynamic Astigmatism (spot shape adjustment) G2 Adjust 'G2 adjustment should be performed by BARCO personnel, or BARCO authorized dealers'. EXIT Gamma corrections ENTER Projector Warm Up CRT Drive Mode Messages, warnings and failure codes 8 Messages, warnings and failure codes Options IR Receiver 800 Hardwired RCU. 9 shield conductor Projector Control software RCVDS 05 Source Selector VS05 Switcher Options MAGIK Interface Adapter and communication cables Ceiling Mount kit CM100 Orbiting Kit A Orbiting (option) Orbiting Mode Toggle Switches Master/Slave Toggle Orbiting ON/OFF toggle (only in Master Orbiting) Orbiting Speed Toggle (only in MASTER Orbiting) ENTER EXIT Orbiting Alignment Adjustment procedure Stand-Alone projector : ENTER Adjustment procedure multiple projector installations : Adjustment Blocks and Source Numbers 90-99 Adjustment Blocks (memory blocks) B NUMBERS 90 - 99 Source numbers 90 - 99 Insert Card INSERT CARD i-1 5975847 BARCOGRAPHICS 1208S 220197 RCU