Manuals / Brands / Personal Care / Wheelchair / Barco / Personal Care / Wheelchair

Barco R9000893, R9000896 Selecting Setup Pattern, Internal Cross Hatch Pattern

1 55

Download 55 pages, 2.1 Mb

Random Access Adjustment Mode

6-3

5975847 BARCOGRAPHICS 1208S 220197

Selecting Setup Pattern

If an external source is connected to the projector, this menu will be displayed. Push the

control stick forward or backward to highlight the desired setup pattern and then press

ENTER.

Genlocked pattern : internally generated cross hatch pattern, locked on the external source.

Internal # pattern : internally generated cross hatch pattern and locked on internal generated

sync signals. (No external source necessary)

Choose a setup pattern

from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 01

Select with or

then <ENTER>

<EXIT> to return.

ENTER continues to Random Access Adjustment Mode or Internal # Pattern

Selection

EXIT returns to Path Selection menu

ADJUST returns to Operational mode

If no external source is connected to the projector, the internal cross hatch pattern menu will

be displayed.

Note: The menus in this manual are created for an external source, connected to one of the

inputs, and the 'Genlocked Pattern' is selected.

Internal Cross Hatch Pattern

The Internal # pattern menu will be displayed if the internal cross hatch pattern has been

selected or if no source is connected to the projector.

The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are

custom programmable.

Push the control stick forward or backward to highlight the desired cross hatch frequency.

Use the left and right arrow to scroll to another page. Press ENTER. if the desired block is

selected.

kHz/Hz

15.6/50 PAL/SECAM

15.7/60 NTSC

31.2/50 EDTV

31.5/60 IDTV

31.2/50 HDTV EUREKA

31.5/60 HDTV ATV

33.7/60 HDTV HIVISION

15.8/60 EGA 1

61.0/76 VGA 1,2

35.5/87 VGA 4

48.5/60 SUPER VGA 1

44.2/70 SUPER VGA 2

61.0/76 SUPER VGA 3

72.1/67 SUPER VGA 4

89.3/67 SUN 3/260

127.0/60 CHROMATICS

INTERNAL # PATTERN

kHz / Hz

15.6/50 PAL/SECAM

15.7/60 NTSC

31.2/50 EDTV

31.5/60 IDTV

31.2/50 HDTV EUREKA

31.5/60 HDTV ATV

Select with or

scroll with or

<ENTER> to accept

<EXIT> to return

ENTER continues to the Random Access Adjustment Mode.

EXIT returns to the Setup Pattern Selection menu.

Contents

Main Page Page Table of Contents Table of Contents Safety Instructions WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) On safety 1 Notice on Safety PART NUMBER : SER. NUMBER : DEALER : Safety Instructions A. Mains lead (Power cord) with CEE 7 plug B. Power cord with ANSI 73.11 plug 3 4 2 75 ohm Termination Switch for Video signals REAR PANEL TERMINOLOGY Communication Port (800 peripherals) Port 3 Location and Functions of Control b. RCU control panel terminology Back light key ADJ. Address key STBY 3 AC Power (mains) Cord Connection Power Check Switching On/Off Start up with full white image. Signal Input Connection to the Projector : 3-3 5975847 BARCOGRAPHICS 1208S 220197 Connecting a Composite Video source to port 1. VCR S-VHS Audio amplifier Audio amplifier Select 'Selected source' and press ENTER. Highlight 'Picture Tuning' and press ENTER. Connecting a RGB Analog source to port 3. Analog Input Selection : Connecting a RGB Analog source to port 4/5. RGB input selection : 3-5 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) Audio amplifier OFFON Audio amplifier Audio amplifier PERIPHERAL EQUIPMENT 4 How to use your RCU Projector Address a. hardware set up of the projector address. b. How to control the projector. c. Using your RCU. How to display a projector address? Input selection How to program an address into the RCU? Analog Picture Controls Controlling chained projectors. Start Up of the Adjustment Mode 5 Adjustment Mode INSTALLATION GUIDED RANDOM ACCESS Start Up of the Adjustment Mode 6 Starting-Up the Random Access Adjustment mode. ENTER EXIT Overview 'Random Access Adjustment' mode Page Selecting Setup Pattern ENTER EXIT Internal Cross Hatch Pattern ENTER EXIT Random access adjustment mode selection menu. Picture Tuning Color Balance Sync Fast/Slow Adjustment ENTER EXIT Clamp Tuning Peaking Port 2 : Video or S-Video Line Doubler (option) EXIT Color Select ENTER EXIT Focusing ENTER EXIT Focusing color select. ENTER EXIT Midpoint focusing Geometry Adjustments ENTER EXIT ENTER Horizontal Phase Adjustment Raster Shift Adjustment forbidden area projected raster crt faceplate border phosphor border Left-Right (east-west) Adjustments ENTER EXIT Seagull correction Left Side Correction ENTER EXIT Top-Bottom (north-south) Adjustments Seagull Correction ENTER will return to Top-Bottom adjustment menu EXIT will return EXIT Horizontal Size Adjustment ENTER EXIT Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Convergence Adjustment Coarse Convergence Adjustment. Fine Convergence Adjustment. Starting up the Service mode. ENTER EXIT 7 Overview flowchart 'Service' mode. Identification GRAPHICS 1208S Copy a block ENTER EXIT Deletion of blocks Deleting block by block ENTER EXIT Deletion of all blocks ENTER Change password Change Language Run time Set to midposition ENTER will set all settings to their midposition. EXIT will cancel the Undo Midposition Convergence Mid ENTER sets the convergence settings to their midposition. EXIT Dynamic Astigmatism (spot shape adjustment) G2 Adjust 'G2 adjustment should be performed by BARCO personnel, or BARCO authorized dealers'. EXIT Gamma corrections ENTER Projector Warm Up CRT Drive Mode Messages, warnings and failure codes 8 Messages, warnings and failure codes Options IR Receiver 800 Hardwired RCU. 9 shield conductor Projector Control software RCVDS 05 Source Selector VS05 Switcher Options MAGIK Interface Adapter and communication cables Ceiling Mount kit CM100 Orbiting Kit A Orbiting (option) Orbiting Mode Toggle Switches Master/Slave Toggle Orbiting ON/OFF toggle (only in Master Orbiting) Orbiting Speed Toggle (only in MASTER Orbiting) ENTER EXIT Orbiting Alignment Adjustment procedure Stand-Alone projector : ENTER Adjustment procedure multiple projector installations : Adjustment Blocks and Source Numbers 90-99 Adjustment Blocks (memory blocks) B NUMBERS 90 - 99 Source numbers 90 - 99 Insert Card INSERT CARD i-1 5975847 BARCOGRAPHICS 1208S 220197 RCU