Barco R9000893, R9000896 A

Orbiting

A-1

5975847 BARCOGRAPHICS 1208S 220197

AORBITING

Orbiting (option)

Static pictures are very often shown on large screen projectors,

espectially in process control and presentation applications. Due to

the fact that the same picture information is shown for a long period

on the same place, picture tubes can be damaged by 'local burn-in'.

To avoid this problem, BARCO has designed special Orbiting circuitry

which moves the picture very slow around a predefined screen area.

The orbiting circuitry has been designed using a very long cycle time

to make the movement of the projected image imperceptible.

Adjustment procedure :

The orbiting path is automatically added to the Random access

adjustment mode menu when installed.

Press ADJUST to enter the adjustment mode and select Random.

The Random Access Adjustment Mode menu will be displayed.

Highlight ORBITING by pushing the joy stick forward or backward and

press ENTER.

Select with or

then <ENTER>

<EXIT> to return.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

CONTR. MODULATION

SOFT EDGE

Orbiting Mode Toggle Switches

The orbiting module is provided with a three pin connector for

connection with the BARCO's BCl link option module, used in multiple

projector installations. For Orbiting, one projector operates as master

wheras the others operate as slave.

Master/Slave Toggle

Highlight 'CHANGE TO SLAVE' with the joy stick and press ENTER

to set the projector as Slave.

<EXIT> to return.

MASTER ORBITING

CHANGE TO SLAVE

MODE : ON

SPEED : FAST

ADJUST DEVIATION

SELECT WITH OR

THEN <ENTERN>

DEVIATION ADJUST :

VERTICAL WITH OR

HORIZONTAL WITH OR

<EXIT> to return.

MASTER ORBITING

CHANGE TO MASTER

MODE : ON

SPEED : FAST

ADJUST DEVIATION

SELECT WITH OR

THEN <ENTERN>

DEVIATION ADJUST :

VERTICAL WITH OR

HORIZONTAL WITH OR

Highlight 'CHANGE TO MASTER' with the joy stick and press ENTER

to set the projector as Master.

Orbiting ON/OFF toggle (only in Master Orbiting)

Highlight 'MODE : ON' with the joy stick and press ENTER to set the

ORBITING OFF.

Highlight 'MODE : OFF' with the joy stick and press ENTER to set the

ORBITING ON.

<EXIT> to return.

MASTER ORBITING

CHANGE TO MASTER

MODE : ON

SPEED : FAST

ADJUST DEVIATION

SELECT WITH OR

THEN <ENTERN>

DEVIATION ADJUST :

VERTICAL WITH OR

HORIZONTAL WITH OR

ENTER toggles between mode on and off.

EXIT returns to the Path selection menu.

Contents

Main Page Page Table of Contents Table of Contents Safety Instructions WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) On safety 1 Notice on Safety PART NUMBER : SER. NUMBER : DEALER : Safety Instructions A. Mains lead (Power cord) with CEE 7 plug B. Power cord with ANSI 73.11 plug 3 4 2 75 ohm Termination Switch for Video signals REAR PANEL TERMINOLOGY Communication Port (800 peripherals) Port 3 Location and Functions of Control b. RCU control panel terminology Back light key ADJ. Address key STBY 3 AC Power (mains) Cord Connection Power Check Switching On/Off Start up with full white image. Signal Input Connection to the Projector : 3-3 5975847 BARCOGRAPHICS 1208S 220197 Connecting a Composite Video source to port 1. VCR S-VHS Audio amplifier Audio amplifier Select 'Selected source' and press ENTER. Highlight 'Picture Tuning' and press ENTER. Connecting a RGB Analog source to port 3. Analog Input Selection : Connecting a RGB Analog source to port 4/5. RGB input selection : 3-5 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) Audio amplifier OFFON Audio amplifier Audio amplifier PERIPHERAL EQUIPMENT 4 How to use your RCU Projector Address a. hardware set up of the projector address. b. How to control the projector. c. Using your RCU. How to display a projector address? Input selection How to program an address into the RCU? Analog Picture Controls Controlling chained projectors. Start Up of the Adjustment Mode 5 Adjustment Mode INSTALLATION GUIDED RANDOM ACCESS Start Up of the Adjustment Mode 6 Starting-Up the Random Access Adjustment mode. ENTER EXIT Overview 'Random Access Adjustment' mode Page Selecting Setup Pattern ENTER EXIT Internal Cross Hatch Pattern ENTER EXIT Random access adjustment mode selection menu. Picture Tuning Color Balance Sync Fast/Slow Adjustment ENTER EXIT Clamp Tuning Peaking Port 2 : Video or S-Video Line Doubler (option) EXIT Color Select ENTER EXIT Focusing ENTER EXIT Focusing color select. ENTER EXIT Midpoint focusing Geometry Adjustments ENTER EXIT ENTER Horizontal Phase Adjustment Raster Shift Adjustment forbidden area projected raster crt faceplate border phosphor border Left-Right (east-west) Adjustments ENTER EXIT Seagull correction Left Side Correction ENTER EXIT Top-Bottom (north-south) Adjustments Seagull Correction ENTER will return to Top-Bottom adjustment menu EXIT will return EXIT Horizontal Size Adjustment ENTER EXIT Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Convergence Adjustment Coarse Convergence Adjustment. Fine Convergence Adjustment. Starting up the Service mode. ENTER EXIT 7 Overview flowchart 'Service' mode. Identification GRAPHICS 1208S Copy a block ENTER EXIT Deletion of blocks Deleting block by block ENTER EXIT Deletion of all blocks ENTER Change password Change Language Run time Set to midposition ENTER will set all settings to their midposition. EXIT will cancel the Undo Midposition Convergence Mid ENTER sets the convergence settings to their midposition. EXIT Dynamic Astigmatism (spot shape adjustment) G2 Adjust 'G2 adjustment should be performed by BARCO personnel, or BARCO authorized dealers'. EXIT Gamma corrections ENTER Projector Warm Up CRT Drive Mode Messages, warnings and failure codes 8 Messages, warnings and failure codes Options IR Receiver 800 Hardwired RCU. 9 shield conductor Projector Control software RCVDS 05 Source Selector VS05 Switcher Options MAGIK Interface Adapter and communication cables Ceiling Mount kit CM100 Orbiting Kit A Orbiting (option) Orbiting Mode Toggle Switches Master/Slave Toggle Orbiting ON/OFF toggle (only in Master Orbiting) Orbiting Speed Toggle (only in MASTER Orbiting) ENTER EXIT Orbiting Alignment Adjustment procedure Stand-Alone projector : ENTER Adjustment procedure multiple projector installations : Adjustment Blocks and Source Numbers 90-99 Adjustment Blocks (memory blocks) B NUMBERS 90 - 99 Source numbers 90 - 99 Insert Card INSERT CARD i-1 5975847 BARCOGRAPHICS 1208S 220197 RCU