Bard WL3S Air Conditioning Wall-Mount Model Nomenclature, WA 3S, A 10 B P, Ventilation Options

Air Conditioning Wall-Mount Model Nomenclature

MODEL	WA 3S 3
NUMBER

A 10 B P X X

X X

WA – Right Hand	REVISION
WL – Left Hand	WA - 3
	WL - 2

CAPACITY
	VOLTS & PHASE
3S - 3 Ton
	A - 230/208/60/1
4S - 4 Ton
	B - 230/208/60/3
5S - 5 Ton
	C - 460/60/3

KW

VENTILATION OPTIONS

(See Chart Below)

FILTER OPTIONS

P - 2 inch Pleated

MERV 8

COLOR OPTIONS

X - Beige (Standard)

1 - White

4 - Buckeye Gray

5 - Desert Brown

8 - Dark Bronze

A - Aluminum

S - Stainless Steel

CONTROL MODULES

(See Chart Below)

COIL OPTIONS

X - Standard

1 - Phenolic Coated Evaporator

2 - Phenolic Coated Condenser

3 - Phenolic Coated Evaporator

& Condenser

OUTLET OPTIONS

X - Front (Standard)

Note: For 0KW and circuit breakers (230/208 Volt) or rotary disconnect (460 Volt) applications, insert 0Z in the KW field of the model number.

Ventilation Options

Models			All Models
Description		Factory Installed		Field Installed
		Code No.		Part No.
Blank-Off Plate		B		BOP-5
Motorized Fresh Air Damper		M		MFAD-5
Commercial Ventilator - Motorized with Exhaust		V		CRVMP-5
Economizer - School Versions, Enthalpy 4		S		ECONWMS-E5 23
Economizer - Equipment Bldg., Enthalpy 5		W		ECONWMT-E5 2
Economizer - Equipment Bldg., DB Temp 5		T		ECONWMT-T5 2
Energy Recovery Ventilator - 230 Volt	3	R		ERVF-A5 1
Energy Recovery Ventilator - 460 Volt	3	R		ERVF-C5 1
Door Kit for ERVF (Required)		N/A		WMDK5- 3

1Intake and exhaust can be independently adjusted.

2Insert color to match unit ("X" = Beige; "4" = Buckeye Gray; etc.)

3WMDK Door Kit must be ordered in addition to ERVF Assembly and ECONWMS & color matched to unit ("X" = Beige; "4" = Buckeye Gray; etc.)

4 Partial Full Flow (75% of Rated Cooling CFM). All ECONWMS versions have 3" deep intake hood.

5 Full Flow (100% of Rated Cooling CFM). ECONWMT2 and 3 have 16" deep intake hood; ECONWMT-5 has 18" deep intake hood.

Air Conditioning Control Modules							All Models
		AVAILABLE CONTROL OPTIONS
HPC1	LPC 2	CCM 3	LAC 4	ALR 5	SK 6	DDC 7	Factory Installed Code	Field Installed Part
STD	STD	STD			STD		X	N/A
STD	STD	STD	z		STD		H	CMA-28
STD	STD	STD	z	z	STD		J	Factory Only
STD	STD	STD	z	z	STD	z	V 7	Factory Only

STD = Standard equipment for these specified models.

1 HPC. High pressure control is auto reset. Always used with compressor control module (CCM) which is included. See note 3.

2 LPC. Low pressure control is auto reset. Always used with compressor control module (CCM) which is included. See note 3.

3 CCM. Compressor control module has adjustable 30-second to 5-minute delay-on-break timer. On initial power-up, or any time the power is interrupted, the delay-on-make will be 2-minutes plus 10% of the delay-on-break setting. There is no delay-on-make during routine operation of the unit. The module also provides the lockout feature (with 1 retry) for high and/or low-pressure controls, and a 2-minute timed bypass for low-pressure control.

4 LAC. Low ambient control permits cooling operation down to 0°F.

5 ALR. The alarm relay has a set of normally open and normally closed dry contacts to provide the ability to signal a condition of shutdown on either high or low pressure controls.

6 SK. Start kit standard on all -A single phase models only. Is not used or available for -B or -C three phase models.

7 DDC. Incorporates 4 additional sensors: discharge air temperature, indoor blower airflow, compressor current, and dirty filter. These sensing devices function to input analog data such as temperature, as well as digital data such as airflow, compressor status or filter status.

Bard Manufacturing Company, Inc. Bryan, Ohio 43506 www.bardhvac.com

Due to our continuous product improvement policy, all specifications subject to change without notice.

Before purchasing this appliance, read important energy cost and efficiency information available from your retailer.

Form No.

S3378

November, 2012

Supersedes: S3378-712

Form No.	S3378-1112
Supersedes	S3378-712
Page	12 of 12