BENDIX TABS-6 TRAILER ABS MODULE manual Pigtail Wiring HARNESSes, ECU Connectors

Models: TABS-6 TRAILER ABS MODULE

1 32
Download 32 pages 28.46 Kb
Page 3
Image 3

FIGURE 2 - POWER LINE WITHOUT PLC SIGNAL

FIGURE 3 - POWER LINE WITH PLC SIGNAL

Suggested oscilloscope settings are (AC coupling, 1 volt/ div, 100 µsec/div). The signal should be measured on pin 7 of the J560 connector at the nose of the trailer.

PIGTAIL WIRING HARNESSes

Several pigtail wire harnesses are available to connect the TABS-6 module with ABS and other trailer system components. Pigtail harness are weather sealed at the connector interface and are clearly labeled for proper installation. Because of the over-molded design of the TABS‑6 module wiring harnesses, Bendix recommends that the complete harness be replaced if damage or corrosion occurs.

The following connector options may be present:

Modulator 2 (MOD2), Modulator 3 (MOD3), auxiliary, diagnostic, and additional axle wheel speed sensors.

Note: All TABS-6 modules include the two primary wheel speed sensor connections and therefore these are separate from the pigtail harness.

ECU Connectors

Standard TABS-6 module ECU connectors use a TTMA 97‑99 5‑pin Packard Weather Pack connector for brake light power, constant power, ground, the trailer-mounted ABS indicator lamp and a single auxiliary input/output (I/O).

Premium TABS-6 module ECU connectors use an 18-pin Deutsch DT series connector for the same function as above, plus additional modulators, wheel speed sensors and auxiliary I/O’s.

 

2-Pin Additional

 

 

 

 

 

 

Wheel Speed

 

 

 

 

 

 

Sensor

 

 

 

 

 

5-Pin Power and

Connectors

 

 

18-Pin ECU Connector

 

 

(SAL & SAR)

 

 

 

 

Indicator

 

 

 

 

 

 

Lamp (POWER/

 

 

 

 

 

 

WL)

 

 

 

 

 

 

3-Pin Modulator 2

 

 

 

 

 

 

(MOD2)

 

 

 

 

 

 

 

 

 

 

Premium Pigtail Harness

 

4-Pin Diagnostic

 

 

 

(4S/2M with diagnostic)

 

 

 

 

 

 

 

 

Auxiliary

 

 

 

 

 

 

(Optional)

 

 

 

 

 

3-Pin Modulator 3

 

 

 

 

 

 

(MOD3) (Optional)

 

 

 

 

 

 

5XXX....

 

 

 

 

 

B

 

 

 

 

5XXX...

A

E

 

 

 

 

 

 

 

 

 

 

 

D

C

To TABS-6 Module

To BR9235ABS Modulator

5-Pin Power and

 

 

5-Pin ECU

 

Pigtail

Relay Valve

Indicator Lamp

 

 

 

 

 

Connector

 

 

 

(POWER/WL)

Optional

 

 

Modulator Extension Harness

 

 

 

 

 

 

Standard Pigtail Harness

 

 

 

 

Diagnostic

 

To Diagnostic

To TABS-6 Module

 

 

(2S/1M) with optional diagnostic

 

 

 

 

 

 

Tool

Pigtail

 

 

 

 

 

5XXX...

 

 

 

 

 

 

Diagnostic Tool Harness

To ECU or Pigtail

Wheel Speed Sensor

To WS-24Wheel

 

 

Extension Harness

Speed Sensor

 

 

 

 

 

FIGURE 4 - examples of Pigtail wire harnesses aVAILABLE

Page 3
Image 3
BENDIX TABS-6 TRAILER ABS MODULE manual Pigtail Wiring HARNESSes, ECU Connectors