FAQ-Image, Installation, Features, Service, Current

Function

(default setting / value)

		FAQ-Image
		and
		Installation

		FAQ-
	6	Features and
	.	Service
	INFORMATION	Current
	menu	Current
	menu	Status
		System

Description

Displays possible solutions to problems you may encounter.

Source

Shows the current signal source.

Picture Mode

Shows the selected mode in the PICTURE menu.

Resolution

Shows the native resolution of the input signal.

Color System

Shows input system format: NTSC, PAL, SECAM, or RGB.

Equivalent Lamp Hour

Displays the number of hours the lamp has been used.

Firmware Version

Shows the firmware version of your projector.

52 Operation

Page 52

Image 52

BenQ MP776 ST user manual FAQ-Image, Installation, Features, Service, Current, Status, System

Contents

Welcome MP772 ST/MP776 ST Digital Projector Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearance Installed It from the power supplys power outletServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewLamp cover External control panel Controls and functions Projector Remote control Operating the Laser pointer Auto ModeKeystone/Arrow buttons / Up Replacing the remote control batteries Remote control effective rangeApprox.+15 Positioning your projector Choosing a locationFront Table Front Ceiling Obtaining a preferred projected image size Page Projection dimensions Vertical offset Connection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computer Connecting video source devices Connecting audio Connecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source device Connecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source device Starting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarity Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Press Menu/Exit on the projector or remote Using a security cable lock Utilizing the password functionSetting a password To the Security Settings Entering the password recall procedure If you forget the passwordChanging the password Disabling the password function Correcting keystone Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperatureAbout color temperatures 3D Color Management Setting the presentation timer Selection Description To cancel the timer, perform the following steps How to use the Timer On key?Using the remote control Top-Left Bottom-Left Top-Right Bottom-Right Freezing the image Hiding the image Go to the System Setup Basic Panel Key Lock Utilizing FAQ functionLocking control keys Adjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Operating in a high altitude environment Configuring the Lan Control Settings Personalizing the projector menu displayControlling the projector through a Lan environment If you are in a Dhcp environment Controlling the projector remotely through a web browser If you are in a non-DHCP environment Press Exit to go back to the remote network operation Once the cooling process finishes, a Power Off Ring Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Closed Caption On/Off Enable Caption Version Control By RJ45/RS232Projector IP Lan Control Address Description of each menu Picture Mode TemperatureSave Settings Reference Timer SettingsAuto Power Blank Timer Settings Security QuickAudio Standby Reset All ClosedCaption Lan Control FAQ-Image InstallationFeatures Service Maintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screws that secure the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input MP772 ST Supported timing for PC input MP776 ST Supported timing for Hdmi Hdcp input MP776 ST SXGA85 Signal Format Supported timing for Component-YPbPrinput MP772 ST/ MP776 ST Warranty and Copyright information Limited warrantyCopyright Disclaimer Regulation statements FCC statementEEC statement Weee directive

FAQ-Image

Installation

Features and

Service

INFORMATION

Current

Status

System

Description

52 Operation