Projector exterior view

Front/upper side

Rear/lower side

MP776 ST 14 15 16 17 18 19 20 21 22

MP772 ST

14 15 16	17	19	20	21	22

1.Lamp cover

2.External control panel

(See "Controls and functions" on page 10 for details.)

3.Vent (heated air exhaust)

4.Quick-release button

5.Lens cover

6.Focus ring

7.Vent (cool air intake)

8.Front IR remote sensor

79. Projection lens

810. AC power jack

11.Kensington anti-theft lock slot

912. Rear adjuster foot

13.Ceiling mount holes

14.Rear IR remote sensor

15.RJ45 LAN input jack

16.RS232 control port

17.RGB signal output jack

18.HDMI-input port

19.RGB (PC)/Component Video (YPbPr/ YCbCr) signal input jack

20.S-Video input jack

Video input jack

2321. Audio (L/R) input jacks

22.Audio input jack Audio output jack

23.12V DC output terminal

Used to trigger external devices such as an electric screen or light control, etc. Consult your dealer for how to connect these devices.

24.Speaker grill

4				24

Introduction 9

Page 9

Image 9

BenQ MP776 ST user manual Projector exterior view, Front/upper side Rear/lower side, Lamp cover External control panel

Contents

MP772 ST/MP776 ST Digital Projector Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearance It from the power supplys power outlet InstalledServiced Do not step on the projector or place Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover External control panel Projector Controls and functions Remote control Auto Mode Operating the Laser pointerKeystone/Arrow buttons / Up Remote control effective range Replacing the remote control batteriesApprox.+15 Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Page Vertical offset Projection dimensions Connection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computer Connecting audio Connecting video source devices Connecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source device To connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source device Operation Starting up the projectorOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarity Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Press Menu/Exit on the projector or remote Utilizing the password function Using a security cable lockSetting a password To the Security Settings If you forget the password Entering the password recall procedureChanging the password Correcting keystone Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant ColorAbout color temperatures 3D Color Management Selection Description Setting the presentation timer How to use the Timer On key? To cancel the timer, perform the following stepsUsing the remote control Top-Left Bottom-Left Top-Right Bottom-Right Hiding the image Freezing the image Utilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys Adjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Operating in a high altitude environment Personalizing the projector menu display Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Press Exit to go back to the remote network operation Shutting down the projector Once the cooling process finishes, a Power Off Ring Menu system Menu operationMain menu Sub-menu Options Basic Advanced Control By RJ45/RS232 Closed Caption On/Off Enable Caption VersionProjector IP Lan Control Address Description of each menu Temperature Picture ModeSave Settings Reference Settings TimerAuto Power Blank Timer Quick Settings SecurityAudio Standby Closed Reset AllCaption Lan Control Installation FAQ-ImageFeatures Service Care of the projector Maintenance Setting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input MP772 ST Timing chart Supported timing for PC input MP776 ST SXGA85 Supported timing for Hdmi Hdcp input MP776 ST Supported timing for Component-YPbPrinput MP772 ST/ MP776 ST Signal Format Limited warranty Warranty and Copyright informationCopyright Disclaimer FCC statement Regulation statementsEEC statement Weee directive