Menu operation, Menu system | BenQ MW82IST instruction

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.

Main menu Sub-menu		Options

	Wall Color	Off/Light Yellow/Pink/Light
	Wall Color	Green/Blue/Blackboard
		Green/Blue/Blackboard
	Aspect Ratio	Auto/Real/4:3/16:9/16:10
	Keystone
	Position
	Phase

H. Size

1.Digital Zoom

DISPLAY
DISPLAY			Auto/Top Bottom/Frame
	3D	3D Mode	Sequential/Frame Packing/Side by
	3D		Side/Off
			Side/Off
		3D Sync Invert	Disable/Invert
		Blackboard	Off/Letter Formation/Worksheet/
	Teaching	Blackboard	Coordinate Chart
	Teaching		Coordinate Chart
	Template	Whiteboard	Off/Letter Formation/Worksheet/
		Whiteboard	Coordinate Chart
			Coordinate Chart
	Picture Mode	Dynamic/Presentation/sRGB/Cinema/3D/User 1/
	Picture Mode	User 2
		User 2
	Reference Mode Dynamic/Presentation/sRGB/Cinema/3D
	Brightness
	Contrast
	Color
	Tint
2.	Sharpness
2.	Brilliant Color		On/Off
PICTURE	Brilliant Color		On/Off
PICTURE	Color Temperature		Cool/Normal/Warm
	Color Temperature Fine Tuning		R Gain/G Gain/B Gain/R Offset/G
	Color Temperature Fine Tuning		Offset/B Offset
		Primary Color	R/G/B/C/M/Y
	3D Color	Hue
	Management	Saturation
		Gain
	Reset Picture Setting		Current/All/Cancel
3.	Quick Auto Search		On/Off
SOURCE	Color Space Conversion		Auto/RGB/YUV

36 Operation

Image 36

BenQ MW82IST user manual Menu operation, Menu system, Main menu Sub-menu Options

Contents

MW821ST Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image size Connection Connection Connecting video source devices Connecting audioPlaying sound through the projector About the microphone input Device Operation Starting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarity Correcting keystone Using the menus Below is the overview of the OSD menu Using a security cable lock Utilizing the password functionSetting a password If you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color Management Setting the presentation timer Resetting current or all picture modesSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-Right To activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environment Adjusting the sound Using the test patternTurning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Direct power off Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/4 Hr/8 hr/12 hr BasicBottom-Right/Bottom-Left Min/25 min/30 min Main menu Sub-menu Options System Setup Advanced Equivalent Lamp HourIP Address Color System Description of each menu Picture Mode TemperatureColor Temperature Fine Tuning 3D Color Timer InstallationSettings Search System Setup Basic menu Function Description OperationRemote Receiver System Setup Advanced menu Function Description High AltitudeAudio Lamp System Setup Advanced menu Function Description Reset AllStandby Network Current SystemStatus Maintenance Care of the projector Lamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status Message Replacing the lamp Connect the power and restart the projector Resetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Wall mount installation Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Wall plate Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input KHz Supported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Warranty and Copyright information Limited warrantyCopyright Disclaimer