Supported timing for Video and S-Video inputs

Video mode	Horizontal	Vertical Frequency	Color sub-carrier
Video mode	Frequency (kHz)	(Hz)	Frequency (MHz)
	Frequency (kHz)	(Hz)	Frequency (MHz)
NTSC**	15.73	60	3.58
PAL	15.63	50	4.43
SECAM	15.63	50	4.25 or 4.41
PAL-M	15.73	60	3.58
PAL-N	15.63	50	3.58
PAL-60	15.73	60	4.43
NTSC4.43	15.73	60	4.43

**Supported timing for non-3D and 3D signal with Frame Sequential format.

66 Specifications

Page 66

Image 66

BenQ MW851UST, MX850UST user manual Supported timing for Video and S-Video inputs

Contents

Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Installation Inverted images for ceiling mount Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up Down MIC/VOL + Operating the Laser pointerMute Numeric buttons Remote control effective range Replacing the remote control battery Positioning your projector Choosing a locationFront Ceiling Projection dimensions Obtaining a preferred projected image size 808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942 Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best About the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector Device Operation Starting up the projectorOperation Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER If you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alteration Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys To activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen Adjusting the sound Controlling the projector through a LAN environmentCable connection Controlling the projector remotely through a web browser If you are in a non-DHCP environment Iiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hr Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description Teaching Search TimerSettings Color Space Panel Key Function DescriptionOperation Lock Audio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function DescriptionReset All Network System Information menu Function DescriptionCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out of the projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Indicators Light Status & Description Power eventsLamp events Troubleshooting Specifications Projector specifications Dimensions Mm W x 236.9 mm H x 322.8 mm D 339 Specifications Wall mount installation Minimum installation requirements 975 1173 1189 1181 960 Minimum Ceiling Height mm = f + H + b + 60 + 221+ c CeilingWall plate Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput TimingHorizontal Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer