Minimum Ceiling Height mm = f + H + b + 60 + 221+ c | BenQ MW851UST

Minimum Ceiling Height (mm) = f + H + b + 60 + 221+ c

c

60

221

b

H

	Ceiling
	a
	322.8
screen	D
	D
	W

fDistance from floor to bottom of image

floor

e

Projection area

20 60

				150	180
				150	180

Wall plate

• The dimensions are based on the BenQ wall mount (P/N: 5J.J4V10.001).

•There is 3% tolerance among these numbers due to optical component variations. BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

•The dimensions supplied are offered as a guide only and may differ depending on several factors relating to any specific installation.

•The dimensions are based on the projector being configured with zero keystone correction.

•The dimensions assume that the wall mount arm is positioned 90° from the bottom case of projector and screen surface.

62 Specifications

Image 62

BenQ MW851UST, MX850UST user manual Minimum Ceiling Height mm = f + H + b + 60 + 221+ c, Wall plate

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearance Installation Inverted images for ceiling mount Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Projector Test Remote controlON/OFF Keystone/Arrow buttons / Up Down MIC/VOL + Operating the Laser pointerMute Numeric buttons Remote control effective range Replacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Projection dimensions Obtaining a preferred projected image size 808 Screen Size Distance from Screen in mmDiagonal Inches 1524 1778 1508 942 Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best About the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector Device Operation OperationStarting up the projector Fine-tuning the image clarity Adjusting the projected imageAuto-adjusting the image Correcting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAbout the aspect ratio Aspect alteration Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projected Count Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Remote paging operationsFreezing the image Locking control keys Creating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment Controlling the projector remotely through a web browser If you are in a non-DHCP environment Iiii Iiiv Press Exit to go back to the remote network operation Direct power off Shutting down the projector Main menu Sub-menu Options Menu operationMenu system Min/25 min/30 min System Setup BasicSleep Timer Hr/8 hr/12 hr Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description Teaching Search TimerSettings Color Space Panel Key Function DescriptionOperation Lock Audio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function DescriptionReset All Network System Information menu Function DescriptionCurrent Status Maintenance Care of the projector Lamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Use the handle to slowly pull the lamp out of the projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Specifications Projector specifications Dimensions Mm W x 236.9 mm H x 322.8 mm D 339 Specifications Wall mount installation Minimum installation requirements 975 1173 1189 1181 960 Wall plate Minimum Ceiling Height mm = f + H + b + 60 + 221+ cCeiling Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputTiming Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer