Remote control, On/Off, Test | BenQ MX850UST, MW851UST instruction

Remote control

1	13
2	13
	14
3	15
4	16
	16
5	17
6	16
	16
7	18
8	19
9	20
10	21
11	22
11
12	23
	24

1. ON/OFF

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2, VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.ECO BLANK

Used to hide the screen image.

5. Left

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.LASER

Emits visible laser pointer light for presentation purposes.

8.PAGE UP/PAGE DOWN

Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

9.FREEZE

Freezes the projected image.

10.NETWORK SETTING

Enters network setting directly.

11.TEST

Displays the test pattern.

12.SMART ECO

Displays the lamp mode selection bar.

13.NETWORK

Searches the network signal and project it within a few seconds once available.

14.SOURCE

Displays the source selection bar.

15.Auto

Automatically determines the best picture timings for the displayed image.

16.Keystone/Arrow buttons ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

17. Right

When the On-Screen Display (OSD) menu is activated, the #5, #16 and #17 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11

BenQ MX850UST, MW851UST user manual Remote control, On/Off, Test, Keystone/Arrow buttons / Up Down

Contents

Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Inverted images for ceiling mount Installation Introduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior view Controls and functions Projector Keystone/Arrow buttons / Up Down Remote controlON/OFF Test Numeric buttons Operating the Laser pointerMute MIC/VOL + Replacing the remote control battery Remote control effective range Front Ceiling Positioning your projectorChoosing a location Obtaining a preferred projected image size Projection dimensions 1778 1508 942 Screen Size Distance from Screen in mmDiagonal Inches 1524 808 Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance Device Audio Settings Microphone Volume menuPlaying sound through the projector About the microphone input Operation OperationStarting up the projector Correcting keystone Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarity Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Write down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Aspect alteration Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color Management Selection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count Down Locking control keys Remote paging operationsFreezing the image Hiding the image Creating your own startup screen To activate the High Altitude ModeOperating in a high altitude environment Cable connection Adjusting the soundControlling the projector through a LAN environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Iiii Iiiv Press Exit to go back to the remote network operation Shutting down the projector Direct power off Main menu Sub-menu Options Menu operationMenu system Hr/8 hr/12 hr System Setup BasicSleep Timer Min/25 min/30 min Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save Settings Color Space TimerSettings Search Lock Function DescriptionOperation Panel Key Lamp System Setup Advanced menu Function Description HighAltitude Audio Network System Setup Advanced menu Function DescriptionReset All Standby Status Information menu Function DescriptionCurrent System Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Replacing the lamp Use the handle to slowly pull the lamp out of the projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications Specifications Mm W x 236.9 mm H x 322.8 mm D 339 Specifications Dimensions Minimum installation requirements Wall mount installation 975 1173 1189 1181 960 Wall plate Minimum Ceiling Height mm = f + H + b + 60 + 221+ cCeiling Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputTiming Supported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright