Connecting a Component Video source device | BenQ MW516, MX514

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output jacks available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device. Match the color of the plugs to the color of the jacks; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER IN-1or COMPUTER IN-2jack on the projector.

3.If you wish to make use of the projector speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO jack of the projector.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 23

Image 23

BenQ MW516, MX514 Connecting a Component Video source device, To connect the projector to a Component Video source device

Contents

User Man ual Table of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector features Shipping contents Rear/lower side Projector exterior view Controls and functions Ceiling mounting the projector Remote control Freeze Volume +Source Mute Replacing the remote control battery Front Ceiling Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Page Max length Set mm Inch Max. zoom Age Min. zoom Projection dimensions Connection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitor Connecting Video source devices To connect the projector to an Hdmi source device Connecting an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source device To connect the projector to an S-Video/Video source device Connecting an S-Video/composite source device Starting up the projector Operation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Use build-in test pattern Fine-tuning the image size and clarity Correcting keystone Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a password Changing the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Using Wall Color Press MODE/ENTER and the 3D Color Management page displays Selecting a Color Temperature3D Color Management Creating your own startup screen Go to the System Setup Basic MyScreen menu, press MODE/ENTER Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timer Remote paging operations To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Hiding the image Operating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude Mode Use Teaching Template Personalizing the projector menu display Select the lamp saver modeUntil the System Setup Advanced menu is highlighted 100% dynamically by detecting the content brightness level Shutting down the projector Menu system Menu operation System ION Description of each menu Template 3D SyncInvert Teaching Mode Picture ModePicture menu Reference Search TemperatureMenu 3D Color Management Save Settings Quick Auto Brilliant Language TimerSettings Presentation Lock System Setup Basic menuOperation Panel Key Lamp System Setup Advanced menuHigh Altitude Audio Standby Reset AllClosed Caption Status Information menuCurrent System Care of the projector Maintenance Extending lamp life Setting Auto Power OffLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Page Resetting the lamp timer Off Red IndicatorsOff Troubleshooting Optical Specifications 301.7 68.3 71.2 DimensionsCeiling mount installation 232.5 123.4 Supported timing for PC input Timing chart Supported timing for Hdmi input Resolution Horizontal Vertical Pixel Mode Frequency KHz MHz Supported timing for Component-YPbPrinput Patents for MS513/MX514/MW516 Warranty and Copyright information