Specifications, Projector specifications | BenQ MX520 guide

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1024 x 768 XGA

Display system 1-CHIP DMD

Lens F/Number

F= 2.54-2.73 Lamp

210 W lamp

Electrical

Power supply

AC100–240V, 3.4 A, 50-60 Hz (Automatic)

Power consumption

325 W (Max); < 0.5 W (Standby)

Mechanical

Weight

2.3 Kg (5.29 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 2 watt x 1 (MX520)

(Stereo) 10 watt x 1 (MX703) Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 1 (MX520) IR receiver x 2 (MX703) LAN control

RJ45 x 1 (MX703)

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI x 1

Audio signal input Audio in

RCA audio jack (L/R) x 2 PC audio jack x 1 (MX520) PC audio jack x 2 (MX703)

USB port (Mini-B x 1)

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

54 Specifications

Image 54

BenQ MX520 user manual Specifications, Projector specifications

Contents

MX520/MX703 Digital Projector Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Front Table Positioning your projectorChoosing a location Front Ceiling Projection dimensions Obtaining a preferred projected image sizeMX520 MX703 Screen size Projection distance mm Diagonal Min Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation Starting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Using the menus Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function If you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a color temperature Setting a preferred color temperature 3D Color Management Setting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-Right Locking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environment Adjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Direct power off Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Menu Display Sec/10 sec/20 sec/30 sec/Always Time Menu Settings Menu PositionBasic Right/Bottom-Left IP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color System Description of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D Color Settings TimerInstallation Search Remote System Setup Basic menu Function DescriptionOperation Receiver for Color Splash LockBackground Screen Reset All System Setup Advanced menu Function DescriptionSettings for Baud Rate Current SystemStatus Maintenance Care of the projector Lamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status Message Replacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out Projector Maintenance Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input KHz Supported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer