System Setup Advanced menu Function Description | BenQ MX520

5. SYSTEM SETUP: Advanced menu

	Function	Description
		Selects a baud rate that is identical with your computer’s so that you
	Baud Rate	can connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.

	Test Pattern	See "Using the test pattern" on page 33 for details.

		Closed Caption Enable
		Activates the function by selecting On when the selected input signal
		carries closed captions.
	Closed	• Captions: An on-screen display of the dialogue, narration, and
	Closed	sound effects of TV programs and videos that are closed captioned
	Caption	(usually marked as "CC" in TV listings).
		Caption Version
		Selects a preferred closed captioning mode. To view captions, select
		CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
		language in your area).
		Network (for MX703)
		Selecting On enables the function. The projector is able to provide the
		network function when it is in standby mode.
		Monitor Out
		Selecting On enables the function. The projector can output a VGA
		signal when it is in standby mode and the COMPUTER 1 jack is
	Standby	correctly connected to devices. See "Connection" on page 16 for how
	Standby	to make the connection.
	Settings	Audio Pass Through
		Audio Pass Through
		The projector can play sound when it is in standby mode and the
		corresponding jacks are correctly connected to devices. Press / to
		choose the source that you wish to use. See "Connection" on page 16
		for how to make the connection.
		Enabling this function slightly increases the standby power consumption.

		Wired LAN
		See BenQ Network Projector Operation Guide for details.
	Network	AMX Device Discovery
	Settings (for	When AMX Device Discovery is On, the projector can be detected
	MX703)	by AMX controller.
		MAC Address
		Displays the mac address for this projector.

	Reset All	Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Position, Phase, H. Size, User 1,
	Settings
	Settings	User 2, Projector Installation, Color Space Conversion, High
		Altitude Mode, Security Settings, Baud Rate and Network Settings.

44 Operation

Image 44

BenQ MX520 System Setup Advanced menu Function Description, Baud Rate, Test Pattern, Closed, Caption, Standby, Network

Contents

MX520/MX703 Digital Projector Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front Ceiling MX520 Projection dimensionsObtaining a preferred projected image size MX703 Screen size Projection distance mm Diagonal Min Connection Connection Connecting video source devices Connecting audioTerminal name Terminal appearance Best Operation Starting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using the menus Below is the overview of the OSD menu Using a security cable lock Utilizing the password functionSetting a password If you forget the password Disabling the password function Entering the password recall procedureChanging the password Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Selecting a color temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color Management Selection Description Setting the presentation timerResetting current or all picture modes To cancel the timer, perform the following steps Remote paging operationsFreezing the image Top-Left Bottom-Left Top-Right Bottom-Right To activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environment Adjusting the sound Using the test patternAdjusting the sound level Turning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Direct power off Shutting down the projector Main menu Sub-menu Options Menu operationMenu system Menu Settings Menu Position BasicMenu Display Sec/10 sec/20 sec/30 sec/Always Time Right/Bottom-Left Main menu Sub-menu Options System Setup Advanced Equivalent Lamp HourIP Address Color System Description of each menu Picture Mode TemperatureColor Temperature Fine Tuning 3D Color Timer InstallationSettings Search System Setup Basic menu Function Description OperationRemote Receiver for Lock BackgroundColor Splash Screen System Setup Advanced menu Function Description Settings forReset All Baud Rate Status CurrentSystem Maintenance Care of the projector Extending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out Projector Maintenance Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input KHz Timing Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer