Security Settings, Baud Rate, Test Pattern Off/On, Out | BenQ SP840

	Security Settings	Change password
	Security Settings	Power on Lock	Off/On
		Power on Lock	Off/On
	Baud Rate		9600/19200/38400/57600/115200
	Test Pattern		Off/On
		Closed Caption	Off/On
	Closed Caption	Enable	Off/On
	Closed Caption	Enable
5.		Caption Version	CC1/CC2/CC3/CC4
5.	Standby Monitor		Off/On
SYSTEM	Out		Off/On
SYSTEM	Out
SETUP:		Control by	RS232/RJ45
Advanced			Network Status
			DHCP
	Lan Control		Projection IP Address
	Settings	Network Status
	Settings	Network Status	Subnet Mask
			Default Gateway
			DNS
			Apply
	Reset All Settings

•Source

6.• Picture Mode

•Resolution

INFORMA-	• Color System
TION	• Equivalent Lamp Hour
	• Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

English

Operation 49

Image 49

BenQ SP840 Security Settings, Baud Rate, Test Pattern Off/On, Closed Caption, Standby Monitor Off/On, Out, RS232/RJ45

Contents

SP840 Digital Projector Welcome Table of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Introduction Projector features Shipping contents Rear/lower side Projector exterior view Projector Controls and functions Remote control Operating the Laser pointer Replacing the remote control battery Remote control effective range Choosing a location Positioning your projector Obtaining a preferred projected image size English Length Average SP840 projection dimensions Connecting a computer Connecting a computer or monitorConnections To connect the projector to a notebook or desktop computer To connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable With a DVI input socket Connecting Audio Connecting Video source devicesBest video quality Better video quality To connect the projector to an Hdmi source device Connecting Hdmi source devicesAV device Hdmi cable To connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an Audio source device Audio Cable To connect the projector to an S-Video source device Connecting S-Video source devicesVideo Cable AV device Audio Cable To connect the projector to a composite Video source device Connecting Composite Video source devicesAV device Video Cable Audio Cable Starting up the projector Operation Using a security cable lock Using the menusUse / to highlight the System Setup Basic menu Securing the projector Setting a password Utilizing the password functionIf you forget the password As pictured to the right, the four arrow keys Changing the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signal Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using Auto KeystoneKeystone function Selecting the aspect ratio Magnifying and searching for details Letter Box About the aspect ratio Setting the User 1/User 2/User 3 mode Selecting a picture modeGo to the Picture Basic Picture Mode menu Optimizing the image Fine-tuning the image quality in user modes Selecting a Color Temperature Adjusting Clarity ControlSelecting a Color Temperature UserFine Tuning Selecting a Gamma Selection Selecting a White Peaking Adjusting Brilliant Color3D Color Management Selecting a Video Format Selecting Color Space Conversion Remote paging operations Selecting a Film ModeSelecting a 3D Comb Filter Locking control keys Setting the Sleep TimerHiding the image Freezing the image Adjusting the soundOperating in a high altitude environment Adjusting the Treble level Adjusting the sound levelAdjusting the Bass level Turning off the Power on/off Ring Tone Controlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environment Controlling the projector remotely through a web browser Iiii Iiiv Shutting down the projector Personalizing the projector menu display Menu system Menu operation YPbPr Tuning Adjustment Digital Zoom PC & ComponentMenu Settings Auto Power Off Settings Security SettingsReset All Settings Source Picture Mode Resolution Baud Rate Description of each menu Picture Mode Picture Advanced Display menu System Setup Basic menu Hdmi Shows the selected mode in the Picture menu Shows the current signal sourceShows the native resolution of the input signal Displays the number of hours the lamp has been used Care of the projector Maintenance Setting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Loosen the screws that secure the lamp Tighten the screws that secure the lamp Setup Advanced Lamp Settings Off IndicatorsRed Off Green Troubleshooting Projector specifications Specifications Dimensions Supported timing for Computer input Timing chart Supported timing for Component-YPbPr input Resolution Horizontal Vertical Pixel Mode Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs SXGA60 Limited warranty Warranty and Copyright informationCopyright Disclaimer FCC statement Regulation statementsEEC statement Weee directive English