Manuals / Billion Electric Company / Computer Equipment / Network Card

Billion Electric Company 30 user manual

Models: 30

1 209

Download 209 pages 59.73 Kb

Page 174

Manual background

Step 3: Go to Configuration > Dual WAN > General Settings. Select the Fail Over radio button. Under Connectivity Decision, input the number of times BiGuard 30 should probe the WAN before deciding that the ISP is in service or not (3 by default). Next, input the duration of the probe cycle (30 sec. by default) and choose the way WAN ports are probed.

174

Image 174

Billion Electric Company 30 user manual

Contents

Version Release 7.01 FW1.06p BiGuardiBusiness Security Gateway SMB User’s Manual Disclaimer Updated March 28 Copyright InformationBiGuard 30 User’s Manual TrademarksSafety Warnings Chapter 2 Router Applications Table of Contents Chapter 1 Introduction1.3 Package Contents 1.1 Overview 1.2 Product Highlights3.4 Configuring PCs for TCP/IP Networking Chapter 4 Router Configuration3.1 Overview 3.2 Before You Begin 3.3 Connecting Your Router 3.5 Factory Default Settings4.4.2.1 ISP Settings 4.4 Configuration4.3 Quick Start 4.4.2.2 Bandwidth Settings 4.4.2.3 WAN IP Alias5.1 Basic Functionality Chapter 5 Troubleshooting4.5 Save Configuration To Flash 4.6 Logout 5.2 LAN Interface5.6 Restoring Factory Defaults Appendix A Product Specifications Appendix B Customer Support5.4 ISP Connection 5.5 Problems with Date and Time E.1 What is a VPN?E.2.1 IPSec Security Components E.2 What is IPSec?E.2.1.1 Authentication Header AH E.2.2 IPSec ModesH.7 VPN Configuration Appendix H Router Setup ExamplesWhat is Quality of Service? H.12 PPTP Remote Access by Windows XPChapter 1 Introduction 1.1 Overview1.2 Product Highlights 1.3 Package Contents BiGuard 30 iBusiness Security Gateway SMBPower Status WAN1 WAN21.3.2 Rear Panel RESET WAN2 WAN1 LAN 1.3.4 Cabling Chapter 2 Router Applications 2.1 Overview2.2 Bandwidth Management with QoS 2.2.1 QoS Technology2.2.2 QoS Policies for Different Applications VoIP Normal PCs Restricted PClow network latencies to function properly. If bandwidth is being used by other applications such as an FTP server, users using VoIP will experience network lag and/or service interruptions during use. To avoid this scenario, this network has assigned VoIP with a guaranteed bandwidth and higher priority to ensure smooth communications. The FTP server, on the other hand, has been given a maximum bandwidth cap to make sure that regular service to both VoIP and normal Internet applications is uninterrupted policies for different PCs on the network. Policy based traffic shaping lets you better manage your bandwidth, providing reliable Internet and network service to your organization 2.2.6 Management by IP or MAC address 2.2.7 DiffServ DSCP Marking2.2.8 DSCP Matching 2.3 Outbound Traffic2.3.1 Outbound Fail Over 192.168.2.2 1st ConnectionISP 2nd connection 192.168.2.32.4 Inbound Traffic 2.4.1 Inbound Fail OverBefore Fail Over After Fail Over2.4.2 Inbound Load Balancing Remote Access from Internet 2.5 DNS InboundHTTP ISP ISP 2.5.1 DNS Inbound Fail OverAfter Fail Over Before Fail OverDNS Request Heavy load on WANHeavy load on WAN DNS Reply2.6 Virtual Private Networking In the example above, the client is making a DNS request. The request is sent to the DNS server of BiGuard 30 through WAN2 1. WAN2 will route this request to the embedded DNS server of BiGuard 30 2. BiGuard 30 will analyze the bandwidth of both WAN1 and WAN2 and decide which WAN IP to reply to the request 3. After the decision is made, BiGuard 30 will route the DNS reply to the user through WAN2 4. The user will receive the DNS reply with the IP address of WAN1 5. The browser will initiate an HTTP request to the WAN1 IP address 6. The HTTP request will be send to BiGuard 30’s URL Host Map 7. The Host Map will then redirect the HTTP request to the HTTP server 8. The HTTP server will reply 9. The URL Host Map will route the packet through WAN1 to the user 10. Finally, the client will receive an HTTP reply packet2.6.1 General VPN Setup BiGuard ClientBefore Fail Over After Fail Over2.6.2 VPN Planning - Fail Over Before Fail Over BiGuard3.1 Overview 3.2 Before You BeginChapter 3 Getting Started 3.3 Connecting Your Router 3.4 Configuring PCs for TCP/IP Networking 3.4.1 Overview3.4.2.1 Configuring 1. Select Start Settings Network Connections 3.4.2 Windows XP3. Select Internet Protocol TCP/IP and click Properties 5. Click OK to finish the configuration 1. Click Start Programs Accessories Command Prompt 3.4.2.2 Verifying SettingsTo verify your settings using a command prompt 2. In the Command Prompt window, type ipconfig and then press ENTERTo verify your settings using the Windows XP GUI 1. Click Start Settings Network ConnectionsAn IP address between 192.168.1.1 and A subnet mask of 3. Click the Support tab If you are using BiGuard 30’s default settings, your PC should 3.4.3.1 Configuring 1. Select Start Settings Control PanelHave an IP address between 192.168.1.1 and Have a subnet mask of Page 4. In the Local Area Connection window, click Properties 5. Select Internet Protocol TCP/IP and click PropertiesPage 7. Click OK to finish the configuration 3.4.3.2 Verifying Settings1. Click Start Programs Accessories Command Prompt 2. In the Command Prompt window, type ipconfig and then press ENTER If you are using BiGuard 30’s default settings, your PC should haveAn IP address between 192.168.1.1 and A subnet mask of 3.4.4.1 Installing Components 3.4.4 Windows 98 / MeYou must have the following installed If you need to install a new Ethernet adapter, follow these steps An Ethernet adapter TCP/IP protocol Client for Microsoft Networksa. Click Add b. Select Adapter, then Add If you need TCP/IP a. Click Add b. Select Protocol, then click Add c. Select Microsoft. Æ TCP/IP, then OK If you need Client for Microsoft Networks a. Click Add3.4.4.2 Configuring 1. Select Start Settings Control Panel b. Select Client, then click Add3. Restart your PC to apply your changes Page Page 6. Click OK to apply the configuration 1. Select Start Run 2. Type winipcfg, and then click OK 3.4.4.3 Verifying SettingsTo check the TCP/IP configuration, use the winipcfg.exe utility 3. From the drop-down box, select your Ethernet adapterWeb Interface Username admin Password admin LAN Device IP Settings 3.5 Factory Default SettingsA default gateway of An IP address between 192.168.1.1 and A subnet mask ofLAN Port IP address Subnet Mask3.6 Information From Your ISP WAN PortDHCP Static IP PPPoE PPTP Big Pond 1. Select Start Settings Control Panel 3.6.2.1 Windows2. Double-click the Network icon 4. Select Internet Protocol TCP/IP and click Properties Page server address automatically radio button 7. Click OK to save your changes3.7 Web Configuration Interface BiGuard 30 includes a Web Configuration Interface for easy administration via virtually any browser on your network. To access this interface, open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click Go. A user name and password window prompt will appear. Enter your user name and password the default user name and password are admin and admin to access the Web Configuration Interface4.1 Overview Chapter 4 Router Configuration4.2 Status 4.2.1 ARP Table4.2.2 Routing Table Sessions 4.2.5 IPSec Status 4.2.6 PPTP Status 4.2.7 Traffic Statistics4.2.8 System Log 4.2.9 IPSec Log4.3 Quick Start 4.3.1 DHCP4.3.2 Static IP 4.3.3 PPPoE4.3.4 PPTP 4.3.5 Big Pond4.4 Configuration Subnet Mask Enter the subnet mask 255.255.255.0 by default RIP RIP v2 Broadcast and RIP v2 Multicast. Check to enable RIPAddress Mapping 4.4.1.1 Ethernet 4.4.1.2 DHCP Server 4.4.1.3 LAN Address Mapping WAN IP AliasPlease click Create to create a LAN Address Mapping rule IP Alias 4.4.2.1 ISP Settings 4.4.2.1.1 DHCP 4.4.2.1.2 Static IP 4.4.2.1.3 PPPoE 4.4.2.1.4 PPTP Settings 4.4.2.1.5 Big Pond Settings 4.4.2.2 Bandwidth Settings 4.4.2.3 WAN IP Alias 4.4.3.1 General Settings 4.4.3 Dual WAN4.4.3.2 Outbound Load Balance 1. By session mechanism 2. By IP address hash mechanism Choose one by clicking the corresponding radio button4.4.3.3 Inbound Load Balance Refresh Interval The interval refreshes are done. Denoted in seconds Admin. Mail Box The administrator’s email account.e.gadmin@abc.comSerial Number It is the version number that keeps in the SOA record Retry Interval The interval retries are done. Denoted in secondsHost URL The URL to be mapped To add a host mapping URL to the list, click CreateDomain Name The domain name of the local host Private IP Address The IP address of the local host4.4.3.4 Protocol Binding Destination IP Range Interface Choose which WAN port to use WAN1, WAN2Source IP Range All Source IP Click it to specify all source IPs All Destination IP Click it to specify all source IPs4.4.4.1 Time Zone 4.4.4.2 Remote Access Allow Remote Access By Only the PC Please specify the IP Address that is allowed to access4.4.4.3 Firmware Upgrade 4.4.4.4 Backup / Restore 4.4.4.6 Password 4.4.4.5 RestartClick Reset to reset to the default administration password admin 4.4.4.7 System Log Server4.4.4.8 E-mail Alert 4.4.5.1 Packet Filter When the entry is upper, the priority is higher Source IP Select Any, Subnet, IP Range or Single Address Destination IP Select Any, Subnet, IP Range or Single Address4.4.5.2 URL Filter URL Filtering You can choose to Enable or Disable this feature Domains Filtering Click the top checkbox to enable this feature. You can also choose to disable all web traffic except for trusted sites by clicking the bottom checkbox. To edit the list of filtered domains, click Details 4.4.5.3 LAN MAC Filter 4.4.5.4 Block WAN Request 4.4.5.5 Intrusion Detection You can find two items under the VPN section IPSec and PPTP 4.4.6.1 IPSec4.4.6.1.1 IPSec Wizard Connection Name A user-defined name for the connection Back Back to the Previous page Next Go to the next page Back Back to the Previous page Next Go to the next page Next Go to the next page Back Back to the Previous page Next Go to the next page Done Click Done to apply the ruleConfiguring a New VPN Connection 4.4.6.1.2 IPSec PolicyConnection Name A user-defined name for the connection interface if Auto is selected Any Local Address Will enable any local address on the network DPD Setting DPD, Dead Peer Detection Peer Encryption Mode Only Stateless or Allow Stateless and Stateful Click Create to create a new PPTP VPN connection account4.4.6.2 PPTP 4.4.7 QoS WAN1 Outbound Creating a New QoS Rule Bandwidth Type For IP Address4.4.8 Virtual Server For MAC Address4.4.8.1 DMZ 4.4.8.2 Port Forwarding Table 4.4.9 Advanced 4.4.9.1 Static Route 4.4.9.2 Dynamic DNS Wildcard Select this check box to enable the DYNDNS Wildcard 4.4.9.3 Device Management Web Server SettingsSNMP Access Control Device NameSNMP V1 and SNMP4.4.9.4 IGMP 4.4.9.5 VLAN Bridge 4.5 Save Configuration To Flash 4.6 Logout5.1.1 Router Won’t Turn On Chapter 5 Troubleshooting5.1 Basic Functionality 5.1.2 LEDs Never Turn Off5.2 LAN Interface 5.1.4 Forgot My Password5.2.1 Can’t Access BiGuard 30 from the LAN 5.2.2 Can’t Ping Any PC on the LANCheck the corresponding LAN LEDs on your PC’s Ethernet device are on 4. Click OK under Internet Options to close the dialogue If you only want to allow pop-up windows with your BiGuard Disabling All Pop-upsEnabling Pop-up Blockers with Exceptions 5.2.3.1 Pop-up Windows4. Ensure that Scripting of Java applets is set to Enabled 5.2.3.3 Java Permissions5.4 ISP Connection 5.3 WAN Interface4. Click OK to close the dialogue If an IP address cannot be obtained 5.5 Problems with Date and Time 5.6 Restoring Factory DefaultsIf an IP address can be obtained, but your PC cannot load any web pages from the Internet Appendix A Product Specifications Availability and ResilienceVirtual Private Network Network Protocols and Features Content FilteringQuality of Service Control FirewallPhysical Interface Physical SpecificationsPower Requirement Operating EnvironmentAppendix B Customer Support Contact BillionAppendix C FCC Interference Statement This device may not cause harmful interferenceAppendix D Network, Routing, and Firewall Basics D.1 Network BasicsD.1.1.1 Net mask D.1.1.2 Subnet Addressing D.1.1.3 Private IP Addresses10.0.0.0 172.16.0.0 192.168.0.0 from these ranges Routers can vary in performance and scale, the types of physical WAN connection they support, and the number of routing protocols supported. BiGuard 30 offers a convenient and powerful way for small-to-medium businesses to connect their networks D.2 Router BasicsD.3.1.2 Denial of Service DoS Attack D.3 Firewall BasicsD.3.1.1 Stateful Packet Inspection With a LAN connected to the Internet through a router, there is a chance for hackers to access or disrupt your network. A simple NAT router provides a basic level of protection by shielding your network from the outside Internet. Still, there are ways for more dedicated hackers to either obtain information about your network or disrupt your network’s Internet access. Your BiGuard 30 provides an extra level of protection from such attacks with its built-in firewall Appendix E Virtual Private Networking E.1 What is a VPN?E.2 What is IPSec? VPNs are traditionally used three waysE.2.1.1 Authentication Header AH There are three major functions of IPSecE.2.1.2 Encapsulating Security Payload ESP ESP divides its fields into three components…E.2.1.3 Security Associations SA SA is identified by 3 parametersTC Dat E.2.3 Tunnel Mode AHAH/E AH/EESP Authentication Quick Mode With PFS Main ModeAggressive Mode Quick Mode Without PFSencryption algorithm, hash algorithm, and authentication method F.1 IPSec Log Event CategoriesF.2 IPSec Log Event Table encryption algorithm, hash algorithm, and authentication methodSend Aggressive mode first Sending the third message of main mode. Done for authenticationReceived the third message of main mode. Done for authentication Received Aggressive mode firstRejected IKE Messages IKE Negotiated Status MessagesMain/Aggressive mode peer ID is identifier string Received Delete SA payload Deleting ISAKMP State integerISAKMP SA Established IPsec SA Established G.3 How Does QoS Work? G.2 What is Quality of Service?G.1 Overview Appendix G Bandwidth Management with QoSG.4 Who Needs QoS? G.4.1 Home UsersPriority ApplicationData Ratio % ApplicationH.1 Outbound Fail Over Appendix H Router Setup ExamplesPage H.2 Outbound Load Balancing Step 2 Configure your WAN2 ISP settings and click Apply Step 6 Click Save Config to save all changes to flash memory H.3 Inbound Fail Over General Settings. Select the Fail Over radio buttonStep 2 Configure Fail Over options if necessary Step 4 From the same menu, set the WAN2 DDNS settings Step 5 Click Save Config to save all changes to flash memoryAfter Fail Over H.4 DNS Inbound Fail OverBefore Fail Over 1st connectionEnable radio button and configure DNS Server 1 by clicking Edit Step 3 Input DNS Server 1 settings and click ApplyHeavy load on WAN H.5 DNS Inbound Load BalancingHeavy load on WAN DNS RequestStep 3 Go to Configuration Dual WAN Inbound Load Balance Host URL Balance radio buttonMapping and configure your FTP mapping Step 4 Next configure your HTTP mappingStep 5 Click Save Config to save all changes to flash memory inbound and outbound bandwidth H.6 Dynamic DNS Inbound Load BalancingRemote Access from Internet HTTPStep 2 Go to Configuration Dual WAN General Settings and enable Load Balance mode. You may then decide whether to enable Service Detection or not WAN1 Page H.7 VPN Configuration H.7.1 LAN to LANLocal Branch OfficeHead Office RemoteH.7.2 Host to LAN Single clientHead Office After Fail Over H.8 IP Sec Fail Over Gateway to GatewayBefore Fail Over ProposalPage Page Branch A H.9 VPN ConcentratorBiGuard BiGuardand configure the and configure the H.10 Protocol Binding Step 5 Click Save Config to save all changes to flash memoryBalancing radio button Step 2 Go to Configuration Dual WAN Protocol Binding and configure settings for WAN1 Internet H.11 Intrusion DetectionH.12 PPTP Remote Access by Windows XP InternetApply Step2 Click Create to create a PPTP AccountStep3 Click Apply, you can see the account is successfully created Step4 Click Save Config to save all changes to flash memory Step5 In Windows XP, go Start Settings Network ConnectionsStep6 In Network Tasks, Click Create a new connection, and press Next Step7 Select Connect to the network at my workplace and press NextStep8 Select Virtual Private Network connection and press Next Step9 Input the user-defined name for this connection and press NextStep10 Input PPTP Server Address and press Next Step11 Please press FinishStep12 Double click the connection, and input Username and Password that defined in BiGuard PPTP Account Settings Internet H.13 PPTP Remote Access by BiGuardInternet Branch OfficeStep4 Click Save Config to save all changes to flash memory Step2 Click Create to create a PPTP AccountStep3 Click Apply, you can see the account is successfully created Step6 Click Apply, and Save CONFIG